Running A Program - Nordcap MORETTI T75G Mode D'emploi

coloured, the status icon turns red and the message bar concurrently
indicates that the heating process has begun .The configuration will
hold until the oven reaches the set point temperature.
The conveyor, by default is activated only when it reaches the
working temperature, as described in 3.6.11.
NOTE:
EACH TIME THE OVEN MUST REACH THE
SET TEMPERATURE AT STARTUP ANDTEMPERATURE
CHANGE, THE ELECTRONIC REGULATION REQUIRES A
FEW MINUTES FOR DIRECT ULTIMATE CALIBRATION;
WAIT FOR THE TEMPERATURE TO BE STABILIZED
BEFORE BAKING, OTHERWISE THE FOOD WILL NOT
COOK PROPERLY
NOTE:
If the START key is not pressed when the oven is
turned on, the display enters power save mode after a limited set
time and goes black. Press any key on the unit to configure
display.
T64G:
The display (figure 31b item D) will show previous cooking mode:
manual or preset program.
If you wish to start cooking, press the "Start" button (fig. 31b item 17)
after which the heating elements, the belt and the fan inside the oven
will start (fig. 31b item D). The screen will show the message
"HEAT", which will flash until the set point temperature is reached. If
the set point temperature is reached, a message will appear on screen
with "GO" after which you can start cooking. The dot in the
temperature display indicates if power is supplied.
3.6.5 SETTING AND MODIFYING COOKING
PARAMETERS:
This function can only be accessed provided the Lock has not been
enabled!!
To reset parameters before starting the oven (temperature, cooking
time) press + and – to change the set-point temperature and the arrow
keys up/down to edit cooking time.
On T64G, the corresponding display will flash to show the setting has
been selected; you can select three settings: temperature, baking time
and baking program. The selected setting will start flashing. If you
select the "baking program" setting, the temperature display will show
the set point for that program.
Once the required value has been selected, use the up and down arrow
keys to change the value.
NOTE:
The above operation can also be performed when
cooking; if you're on a generic program press "esc" and
automatically enter the manual "mode".
- Maximum temperature set point:
400 °C / 752°F (T75G) o 320°C / 608°F (T64G-TT98G).
-Minimum cooking time:
2 minutes (optional: T75G TT98G 45").
30 seconds (T64G)
- Maximum cooking time:
20 minutes (optional 10 '
T75G-TT98G
The conveyor belt gear motor is fitted with a reverse rev control which
, regardless of the weight on the belt, guarantees
(only for T75G-TT98G)
an even transit time. Cooking time can also be set at zero and the
conveyor belt will stop while the "conveyor belt lock" icon status will
be enabled.
To check the transit time on T75G it is necessary to measure the time
from the moment of entry at the outer side of the baking chamber to the
moment of exit at the outer side of the baking chamber.
To check the transit time on T64G and TT98G, it is necessary to
measure the time from the moment of entry at the outer side of the
baking chamber to the moment of exit at the outer side of the baking
chamber.
3.6.6

RUNNING A PROGRAM

T75G-TT98G
If the oven is on the "manual" mode or on a different program, press
the P button which opens the list of programs in numeric order to select
the desired program. Scroll with the arrow keys up/down (fig. 12, item.
31) until the desired program and press OK to start the program
chosen. The program data appears on the display. Press the START
button to enable cooking.
To SEARCH BY NAME, or to retrieve a program used recently, see
item 3.6.7.
).
NOTE:
The above operation can also be performed during
cooking and if you are on a generic program, press "esc" and
automatically enter the new program.
NOTE:
If there are no pre-loaded programs, the message
<EMPTY LIST> is displayed, thus it is necessary to enter at least
one cooking program as described in 3.6.7.
T64G
If, when the oven is turned on, it is set to "manual" or to a different
program from the one required, simply use the display (item D will
flash) with the "Left Arrow" (or "Right Arrow"), then select the
desired program indicated by "Pr" with the "Arrow up" or "Arrow
down". If you browse through the programs display,temperature and
baking time show the set values of the selected program.
If the program required is reached, press OK to confirm. If ok is not
selected after a few seconds the display will show the previously set
program.
3.6.7 "PROGRAMS SETTING"
3.6.7.1 MODELS T75G-TT98G
Operating the programs enables the operator to use the "automatic"
mode, i.e. the ability to save and/or retrieve a configuration of
parameters previously set.
NOTE:
Each program is identified by a unique name to which
multiple programs with the same name cannot be set.
A running program is shown in the status icon with the "P" symbol and
in the message bar by the name of the program.
Enter the dedicated menu to manage the programs. Press the MENU
button, click the "programs" item with the up/down arrow keys and
press OK to enter the submenu.
Scroll the up/down arrow keys on the display to select the following
items:
- "Recent": displays the list of recently used programs
- "Search by name": sorts programs starting with the letter desired
- "Insert new": start the procedure to create a new program
- "Edit": start the procedure to edit a new program
- "Delete": start the procedure to delete a new program
- "Import USB": start the procedure to import programs stored on a
device into the internal memory External USB
- "Export" USB: starts the procedure to copy existing programs in
the internal memory on external USB device
•
RECENT
It is the function that lists the latest programs used. Select the desired
program with the up/down arrow keys and then press OK to operate.
Press START to start heating/cooking time with the parameters of the
selected program.
•
SEARCH BY NAME
This is the function that lists all programs stored in the memory in
alphabetical order beginning with the chosen letter via the up/down
arrow keys. Confirm your choice with OK. Select the desired program
with the up/down arrow keys and then press OK to operate. Press
START to start heating/cooking time with the parameters of the
selected program.
•
ENTER NEW
A new program can be entered in two ways:
- Direct storage
- Enter from "Programs" menu
If the oven is on "manual" mode, the direct storage operation allows
you to match a name to the set of parameters used. Hold the "P"
button for a few seconds when the cooking parameters to be stored
are displayed on the main screen.
Alternatively you can enter a new program from the "Programs"
menu: press MENU, select PROGRAM, press OK, select ENTER
NEW and press OK to enter.
In both cases the screen to edit the name is entered (fig. 32a). A
blinking cursor above the display indicates that you must enter the
first letter of the name . Select the desired program with the up/down
arrow keys and then press OK to confirm. Enter the second letter and
so on. If the last letter entered needs to be deleted, scroll up to "DEL"
and press OK or press MENU as many times as each letter to be
deleted. To complete entering the name, and then enter cooking
parameters, scroll down to "END" then Press OK or, alternatively,
press P to enter the set-point temperature and cooking time (Fig. 3
UK/9