Nordcap MORETTI T75G Mode D'emploi page 47

2b). Edit temperature with "+" and "-". Edit cooking time by pressing
TIME with up / down arrow and confirm the parameters entered with
OK.
TT98G: If the 2-temperature display is enabled ,there are two set
temperatures. Use the up "+" and "-" keys for the left temperature,
the down "+" and "-" keys to edit the right temperature. See Par.
3.6.13.
NOTE:
if the programs entry screen is accessed from the
main screen when P is held (direct storage method) the cooking
parameters cannot be edited!
At this point the summary program is displayed (fig. 32 c). Press OK
to save the program and operate.
Press RETURN several times to return to the previous screens
without saving.
•
EDIT
A program can be edited in two ways:
- Edit directly
- Edit from "Programs" menu
If the oven is on "Programs" mode, run the direct editing operation by
pressing and holding "P" for a few seconds until the edit screen with
the current program parameters is displayed.
Alternatively you can edit an existing program from the programs
menu: press MENU, select "programs", press OK, select "Edit",
confirm with OK. The list of programs will be displayed at this point.
Select the desired program with the up/down arrow buttons and press
OK to edit.
In both cases you enter the edit name, temperature and cooking time
screen.
To edit the parameters follow the previous instructions "Enter new":
•
DELETE
To delete a program in the memory of the control unit, proceed as
follows: press the MENU button.
select "Programs", press OK, select
Delete, confirm with OK. The list of programs will be displayed at this
point in alphabetical order. Select the desired programme with the
up/down arrow buttons and press OK.
Follows a summary screen of the selected program, press OK to
confirm the deletion, RETURN to exit without deleting.
•
USB IMPORT
Insert the USB device into the slot on the left control panel. View the
list of directories present in the USB device. The <ROOT> indicates
the first level of the file system. Select the directory of the programs to
be imported with the up/down arrow keys. The "+" and "-" down
buttons respectively exit and enter the selected directory. Press OK for
import operations. A message displays the number of programs
successfully copied from the USB device to the oven's memory.
Remove the USB device and replace the cap previously removed.
NOTE:
<NO DIRECTORY> indicates that the USB device is
missing or not inserted correctly into its slot
•
USB EXPORT
Insert the USB device into the slot on the left side of the control panel
after removing the cap. The display shows the list of directories present
in the USB device .
<ROOT>indicates the first level of the file system. Select the directory
of the programs to be imported with the up / down arrow keys. The "+"
and "-" down buttons respectively exit and enter the selected directory.
Press OK for export operations. A message displays the number of
programs directly copied from the oven's memory to the USB device.
Remove the USB device and replace the cap previously removed.
NOTE:
the message <NO directory="">indicates that the USB
device is missing or not inserted correctly into its slot
3.6.7.2 MODEL T64G (reference Fig. 31b)
This function can only be accessed if the Lock has not been enabled!!
If you wish to store the 2 characteristic values for a cooking operation
(temperature, cooking time), after setting them as required using the
arrow keys (see point 3.6.5), press the "Program" button.
The message "Pr01" will flash on the display (figure 31b item D).
Select the program to be stored with the "Up Arrow" and "Down
Arrow". Press OK to confirm.
•
EDIT
This function can only be accessed if the Lock has not been enabled!!
If you wish to modify a program that has already been stored, you
must first call it up by pressing the relative key 3.6.6., then modify the
values using the arrow keys. As soon as one of the two values is
edited, the control unit switches to manual mode. To store the new
values, proceed as already described in section 3.6.7.2.
NOTE: On T64G when using the special STEP and RETURN
programs, parameters are automatically modified every time a
baking parameter is changed!
3.6.8 "ECO STAND-BY"
The "Eco standby" key keeps the oven hot reducing gas consumption;
press this key for standby cooking mode.
The oven is provided with two types of stand-by:
- - Eco Stand-by 1: this is enabled with the STAND-BY button
(fig. 31-31b item 19). On the T75G-TT98G the display turns
green and a money box icon is displayed in the operating mode.
On the T64G, the display will show the message "ECO1"
- - Eco Stand-by 2: this is enabled by holding down the STAND-
BY button (fig. 31-31b item 19). In this case besides reducing
gas consumption, the conveyor belt is stopped to preserve its
parts from wear. On the T75G-TT98G the display will show the
icon for the "belt stop" function. On the T64G, the display will
show the message "ECO2"
In both cases, hold the button to disable the key STAND-BY.
NOTE:
The "Eco Standby" mode is similar to an "idle alert of
"the oven and cannot be used during cooking, otherwise food
quality would be compromised.
NOTE:
The function can be enabled only if the oven is in
start mode.
3.6.9 "HOTKEY"
(only for T75G-TT98G)
The "Hotkey" button ("star key") is a direct access custom button with a
specific function selected by the user.
Enter the "Hotkey" menu to view the current setting represented by the
selected item. To assign the "Hotkey" button a different function, move
the selected item with the up/down arrow keys to the desired entry and
press OK to confirm.
If required press the RETURN key to return to the main screen.
Press the HOTKEY to directly enable the selected function.
3.6.10 "STEP" FUNCTION
only)
"Step" is used for discontinuous mode operations which enables the
conveyor belt manually for a single cooking step .
T75G-TT98G
To enable this feature, access MENU, select the item "Step Function"
and press OK. The conveyor belt is stopped, the display turns orange
and the step function icons are stopped.
Place the product to be cooked on the tape then press HOTKEY to
start cooking: the conveyor belt will begin to move to allow cooking
within the set time plus the time necessary to let out the product. After
this the belt will stop until you press HOTKEY.
If the end of a cooking process and the next step takes over 2 minutes,
the oven automatically enters "Eco Standby mode 2". Press HOTKEY
to resume cooking.
To disable "Step", access menu, select "Step Function" and press OK.
T64G
The T64G as well as providing 20 programs, also has two special
programs: STEP and RETURN.
The STEP program (indicated in the D display by "StEP") can be used
when there is a work pause. It enables the conveyor belt for a single
baking step. To use this program, select the STEP item from the
program list. The conveyor belt then stops. Place the product at the
edge of the belt, then press the "P / Hotkey" to start baking: the belt
will start moving to allow the transit of the product in the set time.
After this the belt will stop until you press "P / Hotkey".
The RETURN program (shown in the D display by "rEtu") can be used
for baking times higher than the maximum allowed (or taken out of the
oven on the same side in which it is placed in the oven). The conveyor
belt can then be enabled for a double baking step.
program, select the RETU item from the program list. The conveyor
belt will then stop. Place the product at the edge of the belt, then press
the P / hotkey to start baking. The belt will start moving, then the first
products will be received within the time set then the second ones in
the opposite direction also within the baking set time. Example: 12
UK/10
(all models) AND "RETURN" (T64G
To use this