REMS Power-Press SE Notice D'utilisation page 24

eng
4.1. Inspection/repair
WARNING WARNING
Before any repair work, pull the mains plug or remove the battery! This
work may only be performed by qualifi ed personnel.
The gearbox of the drive unit in the REMS Power-Press SE is maintenance -
free. They operate in a permanent grease fi lling and therefore require no
lubrication. The motor of the REMS Power-Press SE, REMS Power-Press,
REMS Power-Press ACC, REMS Power-Press XL ACC and REMS Power-
Ex-Press P-CEF ACC has carbon brushes. These are subject to wear and
must therefore be inspected or replaced from time to time. Only use genuine
REMS carbon brushes. The REMS Power-Press SE drive unit has a safety
slip clutch. This is subject to wear and must therefore be checked and renewed
from time to time. Use only an original REMS safety slip clutch. In the battery-
operated drive units, the carbon brushes of the motor are subject to wear.
These cannot be replaced; the DC motor must be replaced. The sealing rings
(O-rings) wear in all electro-hydraulic drive units. These must therefore be
checked and renewed from time to time. If the pressing power is insuffi cient or
oil is lost, the drive unit must be inspected and if necessary repaired by an
authorised REMS after-sales service facility.
NOTICE
Damaged or worn pressing tongs, pressing tongs Mini, pressing rings, adapter
tongs, pressing heads or expanding heads cannot be repaired.
4.2. Servicing
WARNING WARNING
Before service work, pull the mains plug or remove the battery!
Keep the pressing tongs, pressing tongs Mini, pressing rings, adapter tongs,
adapter tongs Mini pressing heads and expandin , and particularly their recep-
tacles, clean. Clean heavily soiled metal parts with the REMS CleanM (Art. No.
140119) cleaner, for example, and then protect against rust.
Clean plastic parts (e.g. housing, batteries) only with the REMS CleanM (Art. No.
140119) or a mild soap and a damp cloth. Do not use domestic cleaning agents.
These frequently contain chemicals that can attack plastic parts. On no account
use petrol, turpentine oil, thinners or similar products to clean plastic parts.
Make sure that liquids never get inside the power tool. Never immerse the
power tool in liquid.
5. Trouble
For preventing damages make sure to avoid operating situations like exemplarily shown in Fig. 14 through 16, that no distortion between pressing tongs, pressing
tongs Mini, pressing rings, adapter tongs, adapter tongs Mini, fi tting and drive unit occurs.
CAUTION CAUTION
After the drive unit has been in storage for a long period of time, the overpressure valve must be actuated fi rst by pressing the reset button (13) before putting back
into operation. If it is stuck or stiff, it may not be pressed. The drive unit must be handed over to an authorized REMS customer service workshop for inspection.
5.1. Fault: Drive unit does not work.
Cause:
● Worn carbon brushes.
● Mains lead defective (REMS Power-Press SE, REMS Power-Press,
REMS Power-Press ACC, REMS Power-Press XL ACC,
REMS Power-Ex-Press P-CEF ACC).
● Battery depleted or defective (REMS cordless drive units).
● Drive unit defective.
5.2. Fault: Radial press does not fi nish the pressing, pressing tongs, Mini pressing tongs, pressing ring, adapter tongs, pressing segment do not close fully.
Cause:
● Drive unit overheated (REMS Power-Press SE, REMS Power-Press,
REMS Power-Press ACC, REMS Power-Press XL ACC,).
● Worn carbon brushes.
● Slip clutch defective (REMS Power-Press SE).
● Battery depleted or defective (REMS cordless drive units).
● Drive unit defective.
● Wrong pressing tongs, Mini pressing tongs, pressing ring (pressing contour,
size) or adapter tongs, adapter tongs Mini inserted.
● Pressing tongs, Mini pressing tongs, pressing ring or adapter tongs, adapter
tongs Mini stiff or defective.
● The pressure indicator LED (28) lights red (REMS Akku-Press 22 V ACC),
see 3.6.
24
4.2.1. Pressing tongs, pressing tongs Mini, pressing rings, adapter tongs, adapter
tongs Mini
Pressing tongs, pressing tongs Mini, pressing rings, adapter tongs, adapter
tongs Mini must be checked regularly for smooth action. Clean pressing tongs, tongs Mini must be checked regularly for smooth action. Clean pressing tongs, tongs Mini
pressing tongs Mini, pressing rings and adapter tongs, adapter tongs Mini if
necessary and lightly grease the bolts (12) of the pressing jaws, pressing
segments and adapter jaws, adapter tongs Mini (Fig. 1, 17 – 21) with machine
oil. Remove deposits from the pressing contour (11, 22). Check the proper
functioning of all pressing tongs, pressing tongs Mini, pressing rings, adapter
tongs, adapter tongs Mini regularly with a test pressing with inserted pressing
fi tting. A perfect pressing is only produced with full closure of the pressing
tongs, pressing tongs Mini, pressing ring or pressing segment. After completing
the pressing, check that the pressing jaws (10) close fully at "A" for the pressing
tongs, Mini pressing tongs (Fig. 1), the (PR-3B) pressing ring (Fig. 20) and the
45° (PR-2B) pressing ring (Fig. 21). After completing the pressing, check that
the pressing jaws (10) close fully at "A" and on the opposite side "B" for the
(4G) pressing tongs (Fig. 17) and the (S) pressing tongs (Fig. 18). After comple-
ting the pressing, check that the pressing segments (21) close fully at "A" and
on the opposite side "B" for the (PR-3S) pressing ring (Fig. 19) and the XL
(PR-3S) pressing ring. If a visible burr is created on the pressing sleeve when
closing the pressing tongs, pressing tongs Mini, pressing ring or pressing
segment, the pressing may be faulty or leaking (see 5. Trouble).
Damaged or worn pressing tongs, pressing tongs Mini, pressing rings, adapter
tongs, adapter tongs Mini may no longer be used. In case of doubt, send in the
drive machine together with all pressing tongs, pressing tongs Mini, pressing
rings, adapter tongs, adapter tongs Mini to an authorised REMS service shop
for inspection.
4.2.2. Radial presses
Keep the press tongs receptacle clean, in particular clean the press rollers (5)
and tongs shank (2) at regular intervals and then lightly grease them with
machine oil. Check the functional safety of the drive unit regularly by making
a pressing with the press fi tting that requires the greatest pressing force. If the
pressing tongs, Mini pressing tongs, pressing ring or pressing segments close
completely in this pressing (see above), the drive unit is functioning reliably.
4.2.3. Axial presses
Keep the compression heads (14) and mounting bores in the pressing device
and the pressing device itself clean.
4.2.4. Pipe expanders
Keep the expanding device (15), expanding heads (16) and expanding mandrel
(18) in REMS Akku-Ex-Press Cu ACC, REMS Akku-Ex-Press P, REMS Akku-
Ex-Press P ACC, REMS Akku-Ex-Press P-CEF ACC, REMS Power-Ex-Press
P-CEF ACC clean. Grease the expanding mandrel (18) lightly from time to time.
Remedy:
● Have the carbon brushes or DC motor changed by qualifi ed personnel or an
authorised REMS customer service workshop.
● Have the mains lead replaced by qualifi ed personnel or an authorised REMS
customer service workshop.
● Charge the battery with the rapid charger or change the battery.
● Have the drive unit checked/repaired by an authorised REMS customer service
workshop.
Remedy:
● Let the drive unit cool down for about 10 minutes.
● Have the carbon brushes or DC motor changed by qualifi ed personnel or an
authorised REMS customer service workshop.
● Have the slipping clutch checked/repaired by an authorised REMS customer
service workshop.
● Charge the battery with the rapid charger or change the battery.
● Have the drive unit checked/repaired by an authorised REMS customer service
workshop.
● Check the labelling on the pressing tongs, Mini pressing tongs, pressing ring or
adapter tongs, adapter tongs Mini and change if necessary.
● Do not use the pressing tongs, Mini pressing tongs, pressing ring or adapter
tongs, adapter tongs Mini any further! Clean and lightly grease the pressing
tongs, Mini pressing tongs, adapter tongs, adapter tongs Mini with machine oil
or replace them with new ones.
● Have the drive unit checked/repaired by an authorised REMS customer service
workshop. Re-press the press fi tting or replace it by a new one. Observe the
installation instructions of the press fi tting system.
eng
adapter tongs Mini adapter tongs Mini if