Intended Use - Ryobi RCS1835 Manuel D'utilisation

Deutsch (Übersetzung der originalen Anleitungen)
is released, the spring loaded limb may strike the
operator and/or throw the chain saw out of control.
„
Use extreme caution when cutting brushes and
saplings. The slender material may catch the saw
chain and be whipped toward you or pull you off
balance.
„
Carry the chain saw by the front handle with the chain
saw switched off and away from your body. When
transporting or storing the chain saw always fit the
guide bar cover. Proper handling of the chain saw will
reduce the likelihood of accidental contact with the
moving saw chain.
„
Follow instructions for lubrication, chain tensioning
and changing accessories. Improperly tensioned or
lubricated chains may either break or increase the
chance for kickback.
„
Keep handles dry, clean, and free from oil and
grease. Greasy, oily handles are slippery and can
causing the loss of control.
„
Cut wood only. Do not use chain saw for purposes
not intended. For example: do not use the chain saw
for cutting plastic, masonry or non-wood building
materials. Use of the chain saw for operations
different than intended can result in a hazardous
situation.
„
Causes and operator prevention of kickback
a) Kickback may occur when the nose or tip of the
guide bar touches an object, or when the wood
closes in and pinches the saw chain in the cut.
b) Tip contact in some cases may cause a sudden
reverse reaction, kicking the guide bar up and
back towards the operator.
c) Pinching the saw chain along the top of the
guard bar may push the guide bar rapidly back
towards the operator.
d) Either of these reactions may cause you to lose
control of the saw which could result in serious
injury. Do not rely exclusively upon the safety
devices built into your saw. As a chain saw user,
you should take several steps to keep your
cutting jobs free from accident or Injury.
e) Kickback is the result of tool misuse and /or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below:
1) Maintain a firm grip, with thumbs and fingers
encircling the chain saw handles, with both
hands on the saw and position your body
and arm to allow you to resist kickback force.
Kickback forces can be controlled by the
operator, if proper precautions are taken. Do
not let go of the chain saw.
2) Do not overreach and do not cut above
shoulder height. This helps to prevent
English (Original instructions)
14
unintended tip contact and enables better
control of the chain saw in unexpected
situations.
3) Only use replacement bars and chains
specified by the manufacturer. Incorrect
replacement bars and chains may cause
chain breakage and/or kickback.
4) Follow the manufacturer's sharpening and
maintenance instructions for the saw chain.
Decreasing the depth gauge height can lead
to increased kickback.
„
It is recommended to use a residual current device
with a tripping current of 30mA or less.
„
Ensure that the power cord and the extension cord of
the chain saw cannot become entangled in branches
or any other objects during the usage of the chain
saw.
„
If you are an unexperienced user of the chain saw,
you should practice cutting logs on a saw-horse or
cradle before using the chain saw without these
supporting tools.
„
The chain saw has a high starting current and should
be connected to a robust power supply. The chain
saw should be connected to a power source with
an impedance of Zsysmax=0.12+0.08j or less.
Please consult your electricity provider or authority if
necessary.

INTENDED USE

INTENDED USE
This chain saw is intended for use to cut wood pieces,
trees and wooden logs in domestic use.
Do not use for any task other than those specified in the
chapter 'INTENDED USE'. Furthermore, this product is
not intended to be used for professional tree services.
5(6,'8$/ 5,6.6
Even with the intended use of the appliance there is
always a residual risk, which can not prevent. According
to the type and construction of the appliance the following
potential hazards might apply:
Contact with exposed saw teeth of the saw chain
(cutting hazards)
Access to the rotating saw chain (cutting hazards)
Unforeseen, abrupt movement of the guide bar
(cutting hazards)
Flung out of parts from the saw chain (Cutting /
injection hazards)
Flung out of parts of the work piece
Inhalation of work peace particles
Skin contact with the fuel oil
Loss of hearing, if no required ear protection used
during work.