Door Control; User-Admissible Maintenance Operations; Replacing The Transmitter Battery - Nice AVIO600 Instructions Et Avertissements Pour L'installation Et L'utilisation

––– STEP 6 –––
This user guide should be stored and handed to all users of the
automation.
6.1 – WARNINGS
l Keep at a safe distance from the moving door until it is com-
pletely open or closed; do not transit through the door until it is
completely open and has come to a standstill. l Do not let chil-
dren play near the door or with its commands. l Keep the trans-
mitters away from children. l Suspend the use of the automa-
tion immediately as soon as you notice something abnormal in
the operation (noises or jolting movements); failure to follow this
warning may cause serious danger and accidents. l Do not touch
moving parts. l Regular maintenance checks must be carried out
by qualified personnel according to the maintenance plan. l Main-
tenance or repairs must only be carried out by qualified technical
personnel. l Send a command with the safety devices disabled:
If the safety devices do not work properly or are out of order, the door can
still be operated.
01. Command the door with the transmitter. If the safety devices give
the enable signal, the door opens normally; otherwise, reattempt within 3
seconds and keep the control activated.
02. After approximately 2 seconds the door will start moving in the "man
present" mode, that is, so long as the control is kept activated the door
will keep moving; as soon as the control is released the door will stop.
If the safety devices are out of order, arrange to repair the automation as
soon as possible.
6.2 – Manually releasing and locking
The gearmotor is equipped with a mechanical system that allows for
opening and closing the door manually.
Manual operation must be performed in the case of a power outage or in
the event of anomalies affecting the system.
1 Pull the release cord down until you
hear the carriage being released.
2 The door can now be moved manu-
ally.
The activation of the manual release
may cause an uncontrollable move-
ment of the door if the springs are
weak or broken, or if the door is off-
balance.
To restore the functionality of the automation system, move the door
back in position until you hear the carriage being engaged.
In the event of a gearmotor fault, it is still possible to try release the motor
to check whether the fault lies in the release mechanism.
26 – English
USER MANUAL (to be delivered to the end user)
the gearmotor
6.3 – Door Control
• With radio transmitter
The command associated to each button depends on how it has been
memorised. The supplied transmitter is already memorised; the following
commands can be transmitted by pressing its buttons:
T1
T3
Buttons Paired command
T1 Step-by-Step (SbS)
T2 Partial opening
T3 Open only
T4 Close only
T5 Courtesy light (ON/OFF)
6.4 – User-admissible maintenance operations
The operations that the user must carry out periodically are listed below:
• Cleaning of the surfaces of the devices: use a slightly damp (not
wet) cloth. Do not use substances containing alcohol, benzene,
thinners or other flammable substances; the use of these sub-
stances may damage the devices and cause fires or electric
shocks.
• Removal of leaves and stones: disconnect the power supply be-
fore proceeding, so as to prevent anyone from moving the door.
6.5 – Replacing the transmitter battery
When the battery is flat, the transmitter capacity is significantly reduced.
If, when a button is pressed, the relevant Led turns on then immediately
fades and turns off, it means that the battery is completely flat and should
be immediately replaced.
If instead the Led turns on only for a moment, it means that the battery is
partially flat; the button must be kept pressed for at least half a second for
the transmitter to attempt to send the command.
However, if the battery level is too low to complete the command (and
possibly wait for the response), the transmitter will turn off and the rel-
evant Led will fade. In these cases, normal transmitter operation can be
restored by replacing the battery with another of the same type, while
observing the relevant polarity. To replace the battery, proceed as shown
below.
a
c
Batteries contain polluting substances: do not dispose of them
together with common waste but use the methods set forth in the
local regulations.
[A] Led
T5
T2
T4
[B]
b
d