Remote Memorisation; Deleting All The Radio Transmitters - Nice AVIO600 Instructions Et Avertissements Pour L'installation Et L'utilisation

5.5.1 – Memorisation mode 1
1 Press button PR for at least 3s.
87
PR P3
When the LR LED (Figure 87) illuminates, release the button.
2 Within 10s, press any button on the radio transmitter to be memorised
and hold it down for at least 3s.
If the memorisation procedure is successful, the LR LED will flash 3 times.
3 If there are other transmitters to be memorised, repeat step 2 within the
next 10s, otherwise the memorisation stage will terminate automatically.
5.5.2 – Memorisation mode 2
With the memorisation in mode 2 of the radio transmitter, any one of the
four commands ("Step-by-Step" (SbS), "Partial opening", "Open only"
and "Close only") can be associated to each button.
In Mode 2 each button requires a separate memorisation stage.
1 Press button PR (figure 87) on the control unit as many times as the num-
ber corresponding to the desired command, according to the following table:
Once "Step-by-Step" command (SbS)
Twice "Open partially" command"
3 times "Open only" command
4 times "Close only" command
2 Make sure that the LR LED makes as many quick flashes as the num-
ber corresponding to the selected command.
3 Within 10 s, press the desired button on the radio transmitter to be
memorised, and hold it down for at least 2 s.
If the memorisation procedure is successful, the LR LED will flash 3 times
slowly.
4 If there are other transmitters to be memorised for the same type of
command, repeat step 3 within the next 10s, otherwise the memorisation
stage will terminate automatically.
5.5.3 – Remote memorisation
A new radio transmitter can be memorised in the control unit without
directly operating the buttons on it. You need to have an "OLD" pre-mem-
orised operational radio transmitter. The "NEW" radio transmitter to be
memorised will inherit the characteristics of the OLD one, i.e. if the OLD
radio transmitter was memorised in Mode 1, the NEW one will also be
memorised in Mode 1. In this case, during the memorisation stage you
can press any key on the two transmitters. If, on the other hand, the OLD
Symptoms
The radio transmitter does not emit
any signal (the LED [A] does not
light up)
The manoeuvre does not start and
the "BUS" LED [B] does not flash
The manoeuvre does not start and
the courtesy light [G] is off
The manoeuvre does not start and
the courtesy light flashes a few
times
The manoeuvre starts but inverts
immediately
The manoeuvre is carried out but
the flashing light does not work
The courtesy light always flashes
20 – English
P2 P1
TABLE 13 - fig. 89
Probable cause and possible solution
• Check to see if the batteries are exhausted, if necessary replace them (Paragraph 7.3.4 "Replacing the
remote control battery").
• Make sure that the power cord is properly plugged into the mains outlet
• Check to see if the fuses [E] or [F] are blown; if necessary, identify the reason for the failure and then
replace the fuses with others having the same current rating and characteristics.
• Make sure that the command is actually received. If the command reaches the SbS input, the corre-
sponding "SbS" LED [D] must light up; if you are using the radio transmitter, the "BUS" LED must make
two long flashes.
• Make sure that the STOP input is active, i.e. that the "STOP" LED [C] comes on. If this does not happen,
check the device connected to the STOP input.
• The photocell test which is performed at the start of each manoeuvre is not successful; check the photo-
cells, also according to Table 12 (Paragraph 5.6.1 Photocells).
• The selected force is too low to move the door. Check for possible obstacles and if necessary select a
higher force as described in chapter 5.1 "Advanced adjustments".
• Make sure that there is voltage on the flashing light's FLASH terminal during the manoeuvre (being inter-
mittent, the voltage value is not important: approximately 10-30V
to the lamp; in this case replace the lamp with one having the same characteristics.
• Give a movement command to start the Force Learning procedure. Some maneuvers are performed
automatically.
transmitter was memorised in Mode 2 you must press the button on the
OLD transmitter which corresponds to the desired command, and the but-
ton on the NEW transmitter to which you wish to associate that command.
Holding the two transmitters, position yourself within the operating range
of the automation and perform the following operations:
1 Press the button on the NEW radio transmitter for at least 5s, then release it.
2 Press the button on the OLD radio transmitter 3 times slowly.
3 Press the button on the NEW radio transmitter once slowly.
At this point the NEW radio transmitter will be recognised by the control
unit and will assume the characteristics of the OLD one.
If there are other transmitters to be memorised, repeat all the steps above
for each new transmitter.
5.5.4 – Deleting a single radio transmitter
Only if the system features a radio transmitter, you can delete it from the
memory by proceeding as follows.
If the transmitter is memorised in Mode 1, only one deletion procedure
will be needed and at step 3 you can press any button. If the transmitter
is memorised in Mode 2, one deletion procedure will be needed for each
key memorised.
1 Press the PR button (Figure 88) on the control unit and hold it down.
88
PR P3
2 Wait until the LR LED lights up, then, within three seconds...
3 Press the key on the radio transmitter to be deleted and hold it down for at least
three seconds. If the deletion procedure is successful, the LR LED will flash rap-
idly five times. If the LR LED flashes only once slowly, it means that the deletion
procedure has not been successful because the transmitter is not memorised.
4 If there are other transmitters to be deleted, press the PR key and
repeat step 3 within ten seconds, otherwise the deletion procedure will be
terminated automatically.
5.4.5 – Deleting all the radio transmitters
With this operation all the memorised transmitters are deleted.
1 Press the PR button on the control unit and hold it down (Figure 88).
2 Wait until the LR LED lights up, then wait until it goes off, then wait until
it has flashed 3 times.
3 Release the PR button precisely upon the third flash.
4 Wait approximately 4s for the deletion process to be completed; during
this time the LR LED will flash very quickly.
If the procedure is successful, after a few moments the LR LED will flash
slowly 5 times.
); if there is voltage, the problem is due
P2 P1