Table des Matières
Publicité
Mögliche Störungen und deren Beseitigung
Störungen
Gerät läuft nach Einschalten nicht
an
Höhenverstellung schwergängig
Schrägverstellung schwergängig
Motor erbringt keine Leistung und
erwärmt sich zu stark
Unbefriedigende Schnittleistung
Brennspuren am Sägeblatt
Safety Instructions
Please observe these instructions very carefully to pro-
tect yourself and others from possible injury!
1. Set up the circular saw bench on a base that is
•
firm
•
level
•
non-slip
•
vibration-free.
Keep the site free of tripping hazards.
Ensure adequate lighting conditions.
2. Do not operate the circular saw bench in a moist or wet environ-
ment, nor in the vicinity of combustible liquids and gases.
3. The circular saw must only be operated with all the correctly
mounted guards.
The supplied splitting wedge must be used. Fig. 40 of the "As-
sembly Instructions" shows how the splitting wedge is inserted and
reset.
4. To ensure reliable and safe operation in closed rooms, the circular
saw bench must be connected to a sawdust extractor (e.g. a small
portable dust extractor).
Air velocity at the extractor connection: at least 20 m/s.
Pressure below the atmosphere: 1,6 kN/m² (1600 Pa)
5. Keep children well away from the circular saw bench, and never
leave it unattended.
6. Persons under the age of 18 are not allowed to operate the circular
saw.
7. The operator is responsible for other people within the working
area.
8. Do not wear loose fitting clothes.
Remove rings, wrist-watch and bracelets.
9. Wear ear defenders (sound level at the workplace normally ex-
ceeds 85 dB(A).
10. Never use cracked or distorted saw blades. Only use sharp saw
blades.
11. Do not use circular saw blades made of high-speed steel (HSS).
Use only tools acc. to EN 847-1.
12. Never use defective connecting lines.
The electrical connection and repairs to the electrical parts of
the machine must only be completed by an authorised electrician.
mögliche Ursachen
•
Stromausfall
•
Verlängerungskabel defekt
•
Motorschutzschalter hat ausgelöst
•
Motor oder Schalter defekt
•
Sägeblatt klemmt
•
Mutter M6 (Abb. 6) zu fest angezogen
•
Gewindespindel verschmutzt
•
Führungsteile gleiten nicht in der Kulisse
(Abb. 10)
•
2. Phasenlauf bei Drehstrommotor
•
Verlängerungskabel zu lang oder Kabelquer-
schnitt zu klein
•
Sägeblatt stumpf
•
Sägeblatt stumpf
Beseitigung
•
Sicherung wechseln
•
Kabel überprüfen, defekte Kabel nicht mehr benutzen
•
nach Abkühlzeit Motor wieder einschalten
•
Motor oder Schalter von einem konzessionierten Elektro-
fachmann überprüfen oder reparieren lassen, bzw. durch
Originalersatzteile ersetzen lassen
•
Tischeinlage herausnehmen bzw. Spankastendeckel
abschrauben und Ursache beseitigen
•
etwas lösen
•
säubern und neu ölen
•
Führungsteile neu ölen
•
Sicherungen und Zuleitungen von einem Elektrofachmann
überprüfen lassen
•
siehe unter Inbetriebnahme
•
Sägeblatt schärfen lassen bzw. erneuern
•
Sägeblatt schärfen lassen bzw. erneuern
Local rules and regulations, particularly those concerning protective
measures and labour safety, must be observed.
13. It is impermissible to use wobble saws and groove-milling cut-
ters.
14. When cutting round wood, use facilities that prevent the work-
piece from turning on both sides of the saw blade.
15. Use a pushing stick when rip sawing narrow workpieces (space
between saw blade and rip fence less than 120 mm). Fig. 59
16. Ensure that cut-off parts cannot be caught in the teeth of the saw
blade and forcefully hurled out.
Never use the hands to remove sawdust, chips and waste from the
danger area of the saw blade.
17. Renew the table insert if the sawing gap is damaged or worn out.
18. Always switch off the machine and disconnect the plug from the
mains socket under the following conditions:
Repair work
Maintenance and cleaning work
Remedying faults
Transportation of the saw
Changing saw blades
When the saw is unattended (even during brief intervals)
Normal intended use
•
The circular saw bench is exclusively intended for rip sawing and
cross cutting solid wood and composite boards such as particle
boards, chipboards, coreboards, etc., with a square or rectangular
cross-section, and using CV and HM circular saw blades for this
purpose. The use of saw blades made of high-speed steel (HSS) is
impermissible. The saw blade diameter must be between 300 and
315 mm.
•
Cross cuts may only be performed in conjunction with a mounted
cross-cutting fence.
•
Normal intended use also includes the observance of the manufac-
turer's operating, maintenance and repair conditions, as well as
strict adherence to the safety inspections listed in the instructions.
•
Any other use does not conform with the normal intended use of the
circular saw bench. The manufacturer is not liable for any resulting
damage; the user bears all risks!
6
Publicité
Table des Matières
