Stihl FSA 200.0 R Notice D'emploi page 41

27 Approved Deflector, Cutting Attachment, Handle and Harness Combin...
26.4 Ambient Temperature Limits
WARNING
■ Extreme temperatures can damage the battery
and may also cause it to generate heat, rup‐
ture, leak, ignite or explode, resulting in severe
or fatal personal injury or property damage.
Never charge, use or store the battery outside
the ambient temperature limits specified
below.
► Do not charge the battery below - 4 °F (-
20 °C) or above 122 °F (50 °C).
► Do not use the trimmer / brushcutter or bat‐
tery below ‑ 4 °F (- 20 °C) or above 122 °F
(50 °C).
► Do not store the trimmer / bruscutter or bat‐
tery below - 4 °F (- 20 °C) or above 158 °F
(70 °C).
26.5 Ambient Temperature Recom‐
mendations
For optimum performance, observe the following
ambient temperature ranges for the trim‐
mer / brushcutter and battery:
– Charging: 41 °F to 104 °F (5 °C to 40 °C)
– Use: 14 °F to 104 °F (- 10 °C to 40 °C)
27 Approved Deflector, Cutting Attachment, Handle and Harness
Combinations
27.1 STIHL FSA 200.0 R
The FSA 200 R are approved for use only with the following cutting attachments:
Cutting Attachments
Mowing heads with a
diameter of 14.4 in.
(365 mm):
– PolyCut 28-2 (1)
Mowing heads with
round "quiet" line with a
diameter of 0.095 in.
(2.4 mm):
– AutoCut 25-2 (2)
– AutoCut C 26-2 (3)
– AutoCut 27-2 (4)
– DuroCut 20-2 (5)
– SuperCut 20-2 (6)
0458-041-8201-A
Deflectors
– Deflector for Mowing
Heads
(Ø 450 mm) (13)
– Deflector for Metal
Cutting Attachments
with Skirt and Line
Limiting Blade
(Ø 420 mm) (14)
– Deflector for Metal
Cutting Attachments
with Skirt and Line
Limiting Blade
(Ø 450 mm) (14)
– Deflector for Mowing
Heads
(Ø 450 mm) (13)
– Deflector for Metal
Cutting Attachments
with Skirt and Line
Limiting Blade
(Ø 450 mm) (14)
– Storage: - 4 °F to 122 °F (- 20 °C to 50 °C)
Charging, using or storing the battery outside the
recommended ambient temperature ranges may
reduce performance.
If the battery became damp or wet during opera‐
tion, allow it to dry at least 48 hours at tempera‐
tures between 59 °F (15 °C) and 122 °F (50 °C)
and relative humidity below 70 % before charg‐
ing or storing. Higher humidity can extend the
drying time.
26.6 Engineering Improvements
STIHL's philosophy is to continually improve all
of its products. As a result, engineering changes
and improvements are made from time to time.
Therefore, some changes, modifications and
improvements may not be covered in this man‐
ual. If the operating characteristics or the appear‐
ance of your machine differs from those descri‐
bed in this manual, please contact your STIHL
dealer or the STIHL distributor in your area for
assistance.
26.7 EMC Compliance Statement
for Power Tool and Charger
This Class B digital apparatus complies with
Canadian ICES‑003.
Handle
– Loop Handle (16)
– Loop Handle with Bar‐
rier Bar (17)
English
Harnesses
– Shoulder Strap (18)
– Full Harness (19) with
a quick-release sys‐
tem
– STIHL AR Backpack
Battery in combination
with Hip Pad (20)
– STIHL Battery Belt
with STIHL AP Bat‐
tery Bag with Con‐
necting Cord in com‐
bination with the
Shoulder Strap (21)
– STIHL Battery Belt
with STIHL AP Bat‐
tery Bag with Con‐
necting Cord in com‐
bination with the
Shoulder Harness
and Hip Pad (22)
– STIHL Battery Back‐
pack in combination
with Hip Pad (23)
41