Whirlpool WOI7A8FPT1SBA Manuel Du Propriétaire page 8

on your list of favorites.
ADD FAVORITE?
If you would like to save a function as a favorite and
store the current settings for future use, press
otherwise, to ignore the request press
Once has been pressed, press the
to select the number position, then press
confirm.
Please note: If the memory is full or the number chosen
has already been taken, the oven will ask you to confirm
overwriting the previous function.
To call up the functions you have saved at a later
time, press : The display will show your list of
favorite functions.
1. CONVENTIONAL
Press or to select the function, confirm by
pressing , and then press
. CLEANING
• PYRO
Do not touch the oven during the Pyro cycle.
Keep children and animals away from the oven
during and after (until the room has nished
airing) running the Pyro cycle.
Remove all accessories - including shelf guides - from
the oven before activating the function. If the oven is
installed below a hob, make sure that all the burners
or electric hotplates are switched off while running
the selfcleaning cycle. For optimum cleaning results,
remove the worst soiling with a damp sponge before
using the Pyro function. We recommend only running
the Pyro function if the appliance contains heavy
soiling or gives off bad odours during cooking.
Press to show "Pyro" on the display.
Pyro
Press or to select the desired cycle, then
press to confirm. Once a cycle has been selected,
if desired, press or
delay), then press
Clean the door and remove all accessories as prompted,
then close the door and press
oven will begin the self-cleaning cycle, while the door
locks automatically: a warning message appears on the
display, along with a countdown indicating the status
of the cycle in progress.
Once the cycle has been completed, the door remains
locked until the temperature inside the oven has
.
or
to activate.
to set end time (start
to confirm.
when done: the
returned to a safe level.
• SMARTCLEAN
Press to show "Smart Clean" on the display .
Smart clean
Press to activate the function: the display will
prompt you to do all actions needed to obtain the
to
best cleaning results: Follow the indications and then
press when done. Once you have done all steps,
when required press
cycle.
Please note: It is reccommended to do not open the
oven door during the cleaning cycle to avoid a loss of
water vapor that could get an adverse effect on the
final cleaning result.
An appropriate message will start flashing on the
display once the cycle has finished. Leave the oven to
cool and then wipe and dry the interior surfaces with
a cloth or sponge.
. DRAIN
The drain function allows the water to be drained in
order to prevent stagnation in the boiler. This product
has been developed in order to automatically run a
drain cycle once cooking has been stopped/has
ended.
Approximately 30min after the stop/end of cooking,
the oven will automatically drain the system, moving
the residual water in the drawer (be careful not to
remove the drawer after cooking). Once done, the
drawer can be extracted and emptied. We
recommend emptying the drawer as soon as the
drain is completed.
. DESCALE
This special function, activated at regular intervals,
allows you to keep the steam system in the best
condition. Once the function is started, follow all the
steps indicated on the display. The average duration
of the full function is around 140 minutes.
Descale can be initiated anytime by the user from the
Cleaning Menu.
The display will show you when it is time to run a
Descale cycle (see the table below).
DESCALE MESSAGE
<DESCALE RECOMMENDED>
It appears after around 15
hours of steam cycles*
<DESCALE NEEDED>
It appears after around 20
hours of steam cycles*
*considering the default value (4 - Hard) of water
hardness level. The number of hours of steam cycles
that must pass before the Decale messages are shown
to activate the cleaning
MEANING
It is recommended to run a
Descale cycle.
Descale is mandatory. It is not
possible to run a Steam cycle
until a Descale cycle will be
carried out.