Ryobi RLM46160S Traduction Des Instructions Originales page 7

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 15
the oil fill hole but do not screw in.
Reinstall the oil cap/dipstick and secure.
To check engine oil:
Ensure that the mower is level and area around oil cap/
dipstick is clean.
Remove the oil cap/dipstick. Wipe clean and reseat in
oil fi ll hole but do not screw in.
Remove the oil cap/dipstick again and check oil level.
Add oil as needed.
STARTING/STOPPING THE MOWER
See fig. 6
WARNING
Never start or run the engine inside a closed or poorly
ventilated area; breathing exhaust fumes can kill.
Pre-checks
Check and ensure that the oil level is sufficient by
inspecting the oil level with the dipstick seated.
Check and ensure that the petrol tank has sufficient
regular unleaded fuel.
STARTING THE ENGINE
Firmly push the primer bulb 3 times.
NOTE: This step is not usually necessary when starting
an engine that has already run for a few minutes.
Hold the operator presence control bar down against
the handle.
Pull the starter cord until the engine runs. Do not pull
the starter grip more than 4 times. Release the starter
cord slowly so the rope does not snap back.
NOTE: It may be necessary to repeat priming steps in
cooler weather. In warmer weather, overpriming may cause
fl ooding and engine will not start. If you do fl ood the engine,
wait a few minutes before attempting to start and do not
repeat priming steps.
STOPPING THE ENGINE
Release the operator presence control bar and allow the
engine to come to a complete stop.
PROPELLING THE PRODUCT
See fig. 6
To self-propel: Hold down the operator presence control
while pulling the drive control lever towards the handle.
Release the drive control lever to stop the wheel drive.
To manually propel: Hold down the operator presence
control. Do not engage the drive control lever.
SETTING BLADE HEIGHT
See fig. 7
When shipped, the wheels on the mower are set to a low-
cutting position. Before using the mower for the fi rst time,
adjust the cutting position to the height best suited for your
lawn. The average lawn should be between 38 mm to 50
mm during cool months and between 50 mm and 76 mm
during hot months.
To set the blade height:
Stop the product and wait for the blade to come to a
complete stop.
To raise the blade height, grasp the height adjustment
lever and move it toward the back of the mower.
To lower the blade height, grasp the height adjustment
lever and move it toward the front of the mower.
SETTING THE HANDLE LENGTH
See fig. 8
The height of the handle can be easily adjusted for
operator preference.
Loosen and remove the mid handle knobs.
Remove bolts and washers.
Reinsert bolts and washers in a higher or lower position.
Tighten the knobs.
MOWING TIPS
Make sure the lawn is clear of stones, sticks, wires, and
other objects that could damage the lawn mower blades
or engine. Such objects could be accidentally thrown by
the mower in any direction and cause serious personal
injury to the operator and others.
For best performance, always cut off one-third or less of
the total height of the grass.
When cutting long grass, reduce walking speed to allow
for more effective cutting and a proper discharge of the
clippings.
Do not cut wet grass. It will stick to the underside of the
deck and prevent proper bagging or discharge of the
grass clippings.
New or thick grass may require a narrower cut path.
When the fuel tank is empty and before refuelling, tip
the mower on the left hand side with the fuel cap at the
highest position. This will prevent fuel spillage. Remove
the spark plug lead to prevent accidental starting. The
blade is sharp, avoid contact with it.
Check the blade and underside of deck for any damage
or build up of debris. Clean if necessary. Check security
of the blade bolt.
SLOPE OPERATION
See fig. 9
Slopes are a major factor related to slip-and-fall
accidents that can result in severe injury. Operation on
slopes requires extra caution. If you feel uneasy on a
slope, do not mow it. For your safety, do not attempt to
mow slopes greater than 15 degrees.
Mow across the face of slopes, never up and down.
EN
English
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
5

Publicité

Table des Matières
loading

Table des Matières