Publicité
Stage 20, the cabin
Part
Description
No.
20.1
R.H. inside side panel
20.2
R.H. outside side panel
20.3
L.H. inside side panel
20.4
L.H. outside side panel
20.5
Inside front panel
20.6
Outside front panel
20.7
Inside rear panel
20.8
Outside rear panel
20.9
Cabin housing
20.10
In-fill piece
20.11
Corner piece
20.12
Roof planking
20.13
Outer roof planking
20.14
Roof planking
20.15
Edging strip
20.16
Hatch rail
20.17
Loose bulkhead rail
20.18
Loose bulkhead
20.19
Handrail
20.20
Handrail
20.21
Porthole
20.22
Lifebelt holder
20.23
Lifebelt
-
Glue the panels 20.1 to 20.8 to the moulded cabin housing
20.9 - Fig. 205 (housing not shown).
-
Trim the length of the in-fill pieces 20.10 so that the gap is
the same width all round; Figs. 206 and 207.
-
Attach the corner pieces 20.11.
-
Note: the overhang of the cabin roof over the corner pie-
ces should be 2 mm all round.
-
Glue four roof strakes 20.12 on each side of the centreline,
starting at the centre.
-
Glue the outer strakes 20.13 in place.
-
The remaining gaps are filled with three tapered strakes
20.14 on each side. The strakes have to be tapered from 8
to 4 mm.
-
Glue the edging strips 20.15 in place.
-
Glue the inner rail 20.16 for the sliding hatch to the cabin
Stage 21, the command stand
Part
Description
No.
21.1
Command stand housing
21.2
Side panel
21.3
Rear side panel
21.4
Top side panel
21.5
Front panel
21.6
Top front panel
21.7
Side rear panel
21.8
Back panel
21.9
Top back panel
21.10
Corner piece
21.11
Corner piece
21.12
Bank padding
21.13
Centre padding
All manuals and user guides at all-guides.com
Assembly instructions
Valdivia
Material
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
PVC
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Plywood, ready made
Plywood, ready made
Brass
Plywood, ready made
Plastic
-
-
-
-
-
Material
PVC
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
20
Dimensions
No.
off
Veneer
1
Veneer
1
Veneer
1
Veneer
1
Veneer
1
Veneer
1
Veneer
1
Veneer
1
Vac.
1
2 x 7
7
5 x 5 x 25
4
3 x 7 x 140
8
3 x 10 x 140
2
3 x 10 x 180
6
1.2 x 5 x 140
2
2 x 5 x 70
2
2 x 2 x 25
2
Veneer
2
2 x 45
1
2 x 95
1
12 Ø
2
2
3
34 Ø
1
roof, offset one strake's width to the left of centre. Place
the hatch (17.17) against the first rail as a guide, then glue
the second rail to the cabin roof.
Cut the recess for the loose bulkhead, and glue the rails
20.17 and the loose bulkhead 20.18 to the structure.
Glue the handrails 20.19 and 20.20 to the structure as
shown in Figs. 208 and 209.
The portholes 20.21 have to be sanded back to a thickn-
ess of 1.8 mm. This is done by pushing the porthole firmly
onto the cap of an old cyano bottle to act as a support.
Shorten the cap as shown and sand the porthole down to
the correct depth - Fig. 210.
Glue the prepared portholes to the cabin - Fig. 211.
Glue the lifebelt holders 20.22 to the roof using the lifebelt
20.23 as a guide for correct spacing - Fig. 212.
Dimensions
No.
off
Vac.
1
Veneer
2
Veneer
2
Veneer
2
Veneer
1
Veneer
1
Veneer
2
Veneer
1
Veneer
1
5 x 5 x 20
6
3 x 5 x 20
4
3 x 7 x 70
6
3 x 5 x 35
5
Order No.
1140
Note
Sheet F, FS
Sheet F, FS
Sheet F, FS
Sheet F, FS
Sheet F, FS
Sheet F, FS
Sheet F, FS
Sheet F, FS
Clear
Oversize
Oversize
Sheet F, FS
Sheet E, FS
Sheet E, FS
FS
Sheet E, FS
FS
Note
Clear
Sheet F, FS
Sheet F, FS
Sheet F, FS
Sheet F, FS
Sheet F, FS
Sheet F, FS
Sheet F, FS
Sheet F, FS
Publicité
