Publicité
Stage 16, forward light shaft
Part
Description
No.
16.1
Light shaft housing
16.2
Side panel
16.3
Back panel
16.4
Front panel
16.5
Roof planking
16.6
Washer
-
Glue the side strips 16.2 to the moulded housing 16.1 and
sand back the excess length flush with the ends.
-
Glue the back panel 16.3 and the front panel 16.4 to the
housing. Sand the curved ends flush with the moulding -
Figs. 179 and 180.
-
The finished roof should overhang forward and aft by about
2 mm.
Stage 17, forward companion
Part
Description
No.
17.1
Companion housing
17.2
Bottom side panel
17.3
Top side panel
17.4
Inner back panel
17.5
Outer back panel
17.6
Inner front panel
17.7
Outer front panel
17.8
Front in-fill piece
17.9
Rear in-fill piece
17.10
Corner piece
17.11
Frame strip
17.12
Long window frame
17.13
Short window frame
17.14
Roof planking strake
17.15
Roof planking strake
17.16
Rail
17.17
Sliding hatch core
17.18
Hatch panel
17.19
Hatch roof
17.20
Corner strip
"HL"
Jig strip
17.21
Handle
17.22
Loose bulkhead rail
17.23
Loose bulkhead
17.24
Screw
-
Glue the side panels 17.2 and 17.3 to the moulded com-
panion housing - Fig. 183. Sand back the top edges of
parts 17.2 flush with the glazed area, sanding at a slight
angle to match the glazing panels.
-
Glue the back panels 17.4 and 17.5 to the housing, follo-
wed by the front panels 17.6 and 17.7 - Figs. 184 and 185.
-
Round off the corners of the in-fill pieces 17.8 and 17.9
and glue them in place - Fig. 186.
-
Sand the edges at 45° to accept the 8 corner pieces 17.10.
Glue the corner pieces in place, sand them down to 0.5
mm thickness and round them off - Fig. 187.
-
Notch the corner pieces to accept the frame strips 17.11
and glue the strips in place - Fig. 188.
All manuals and user guides at all-guides.com
Assembly instructions
Valdivia
Material
PVC
Spruce
Spruce
Spruce
Spruce
Brass
-
-
-
-
Material
PVC
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Spruce
Obechi
Spruce
Spruce
Spruce
Spruce
Brass wire
Spruce
Spruce
Steel
-
-
-
18
Dimensions
No.
off
Vac.
1
3 x 5 x 30
2
Veneer
1
Veneer
1
3 x 5 x 36
5
7/3.2 Ø
1
When planking the roof start with the centre strake 16.5 -
Fig. 181.
Chamfer the edges of the strips so that they meet snugly
at the top.
Sand the finished roof as shown in Fig. 182.
Mark the centre of the guide tube 9.1 on the back panel
16.3, and drill the 4 mm Ø hole for it. Glue the washer 16.6
over the hole after installing the light shaft.
Dimensions
No.
off
Vac.
1
Veneer
2
Veneer
2
Veneer
1
Veneer
1
Veneer
1
Veneer
1
2 x 7 x 33
1
2 x 5 x 15
1
5 x 5 x 20
8
2 x 2 x 65
6
1.2 x 5 x 75
4
1.2 x 5 x 20
8
3 x 5 x 80
9
3 x 7 x 100
2
2 x 5 x 70
2
8 x 28 x 35
2
Veneer
4
3 x 5 x 45
12
5 x 5 x 45
12
5 x 5 x 80
1
0.8 x 20
2
2 x 2 x 32
2
Veneer
2
2.2 Ø x 9.5
2
Relieve the upper window frames 17.12 to fit round the
corner pieces, and glue them in place followed by the bot-
tom window frames. Trim the short window frame pieces
17.13 to fit and space them out equally as shown in Figs.
189 and 190.
Glue in place the three central roof planking strakes 17.14
with an equal overhang. Glue the outer strakes in place,
overhanging at the sides by 1 mm. Fit two further strakes
on each side. This will leave a wedge-shaped gap which is
filled with the strakes 17.5; these will need to be tapered to
suit.
Glue the rails 17.16 to the joint between the fourth and fifth
Order No.
1140
Note
Clear
Sheet F, FS
Sheet F, FS
FS
Note
Clear
Sheet F, FS
Sheet F, FS
Sheet F, FS
Sheet F, FS
Sheet F, FS
Sheet F, FS
FS
Sheet F, FS
Sheet F, FS
FS
Publicité
