Dancerctrl (Régulation De Traction Avec Pantin) - ABB DCS550 Manuel D'exploitation

156
DancerCtrl (régulation de traction avec pantin)
Ce macroprogramme exploite la masse et la position du pantin. Sa position est lue sur l'entrée analogique 3 (EntAna3) et
régulée par une référence vitesse supplémentaire issue du régulateur PID (groupe 40). Les paramètres sont réglés
comme ci-dessous lorsque WinderMacro (61.01) = DancerCtrl :
Nom des paramètres
Ref1Sel (11.03)
TorqMaxSPC (20.07)
TorqMinSPC (20.08)
IndepTorqMaxSPC (20.24)
IndepTorqMinSPC (20.25)
SpeedCorr (23.04)
SpeedRefScale (23.16)
TorqSel (26.01)
TorqMuxMode (26.04)
LoadComp (26.02)
KpPID (40.01)
TiPID (40.02)
PID Act1 (40.06)
PID Ref1 (40.13)
PID OutMin (40.16)
PID OutMax (40.17)
PID OutDest (40.18)
PID ReleaseCmd (40.23)
WriteToSpdChain (61.02)
WindUnwindCmd (61.04)
TopBottomCmd (61.05)
WinderOnCmd (61.06)
TensionOnCmd (61.07)
WindSpdOffset (61.14)
DiaLineSpdIn (62.01)
DiaMotorSpdIn (62.02)
DiameterSetCmd (62.04)
AdaptKpDiaActIn (62.10)
AdaptKpOutDest (62.13)
AccActIn (62.17)
InerDiaActIn (62.23)
InerAccActIn (62.24)
InerReleaseCmd (62.28)
TensRefIn (63.01)
TaperDiaActIn (63.02)
TensValueIn (63.03)
TensSetCmd (63.04)
TensRampHoldCmd (63.09)
TensPulseCmd (63.13)
TTT Ref1In (63.18)
TTT Ref2In (63.19)
TTT Ref3In (63.20)
TTT DiaActIn (63.22)
FrictMotorSpdIn (63.31)
FrictReleaseCmd (63.32)
Add1OutDest (64.01)
Add1In1 (64.02)
Add1In2 (64.03)
Add1ReleaseCmd (64.04)
Add2OutDest (64.08)
Add2In1 (64.09)
Add2In2 (64.10)
Add2ReleaseCmd (64.11)
Programme Winder
DancerCtrl
AI1
325 %
-325 %
325 %
-325 %
0 tr/min
1
Speed
TorqSel2601
0 %
1
1000
517 = AI3 ValScaled (5.17)
1901 = Data1 (19.01)
-10 %
10 %
2304 = SpeedCorr (23.04)
Auto
Auto
WindCtrlWord
WindCtrlWord
DI1
Auto
0
202 = SpeedRef2 (2.02)
104 = MotSpeed (1.04)
DI2
6208 = DiameterAct (62.08)
2403 = KpS (24.03)
216 = dv_dt (2.16)
6208 = DiameterAct (62.08)
6221 = AccActAdjust (62.21)
Auto
0
6208 = DiameterAct (62.08)
0
Auto
RelTensRamp
Auto
0
6315 = TensionRef (63.15)
0
6208 = DiameterAct (62.08)
104 = MotSpeed (1.04)
Auto
0
6324 = TensToTorq (63.24)
0
Auto
2602 = LoadComp (26.02)
6230 = InertiaComp (62.30)
6334 = FrictionComp (63.34)
Auto
3ADW000379R0307 DCS550 Manual fr c
Factory (default)
SpeedRef2301
325 %
-325 %
325 %
-325 %
0 tr/min
1
Speed
TorqSel2601
0 %
5
2500
0
0
-100 %
100 %
0
Auto
Auto
WindCtrlWord
WindCtrlWord
Auto
Auto
0
202 = SpeedRef2 (2.02)
104 = MotSpeed (1.04)
NotUsed
6208 = DiameterAct (62.08)
0
216 = dv_dt (2.16)
6208 = DiameterAct (62.08)
6221 = AccActAdjust (62.21)
Auto
0
6208 = DiameterAct (62.08)
0
Auto
RelTensRamp
Auto
0
6315 = TensionRef (63.15)
0
6208 = DiameterAct (62.08)
104 = MotSpeed (1.04)
Auto
0
6324 = TensToTorq (63.24)
0
Auto
0
6230 = InertiaComp (62.30)
6334 = FrictionComp (63.34)
Auto