Indirecttens (Régulation De Traction Indirecte) - ABB DCS550 Manuel D'exploitation

152
IndirectTens (régulation de traction indirecte)
Ce macroprogramme est une régulation en boucle ouverte, donc sans retour capteur (traction réelle non mesurée). La
traction est régulée à partir de courbes de diamètres et de préréglages de l'inertie et du frottement. Le régulateur de
vitesse reste activé, mais est saturé. Cette régulation est très robuste car elle ne nécessite aucune mesure physique de
traction. Les paramètres sont réglés comme ci-dessous lorsque WinderMacro (61.01) = IndirectTens :
Nom des paramètres
Ref1Sel (11.03)
TorqMaxSPC (20.07)
TorqMinSPC (20.08)
IndepTorqMaxSPC (20.24)
IndepTorqMinSPC (20.25)
SpeedCorr (23.04)
SpeedRefScale (23.16)
TorqSel (26.01)
TorqMuxMode (26.04)
LoadComp (26.02)
KpPID (40.01)
TiPID (40.02)
PID Act1 (40.06)
PID Ref1 (40.13)
PID OutMin (40.16)
PID OutMax (40.17)
PID OutDest (40.18)
PID ReleaseCmd (40.23)
WriteToSpdChain (61.02)
WindUnwindCmd (61.04)
TopBottomCmd (61.05)
WinderOnCmd (61.06)
TensionOnCmd (61.07)
WindSpdOffset (61.14)
DiaLineSpdIn (62.01)
DiaMotorSpdIn (62.02)
DiameterSetCmd (62.04)
AdaptKpDiaActIn (62.10)
AdaptKpOutDest (62.13)
AccActIn (62.17)
InerDiaActIn (62.23)
InerAccActIn (62.24)
InerReleaseCmd (62.28)
TensRefIn (63.01)
TaperDiaActIn (63.02)
TensValueIn (63.03)
TensSetCmd (63.04)
TensRampHoldCmd (63.09)
TensPulseCmd (63.13)
TTT Ref1In (63.18)
TTT Ref2In (63.19)
TTT Ref3In (63.20)
TTT DiaActIn (63.22)
FrictMotorSpdIn (63.31)
FrictReleaseCmd (63.32)
Add1OutDest (64.01)
Add1In1 (64.02)
Add1In2 (64.03)
Add1ReleaseCmd (64.04)
Add2OutDest (64.08)
Add2In1 (64.09)
Add2In2 (64.10)
Add2ReleaseCmd (64.11)
Programme Winder
IndirectTens
AI1
120 %
-120 %
325 %
-10 %
0 tr/min
1
Speed
TorqSel2601
0 %
5
2500
0
0
-100 %
100 %
0
Auto
Auto
WindCtrlWord
WindCtrlWord
DI1
Auto
150 rpm, connected to SpeedCorr (23.04)
202 = SpeedRef2 (2.02)
104 = MotSpeed (1.04)
DI2
6208 = DiameterAct (62.08)
2403 = KpS (24.03)
216 = dv_dt (2.16)
6208 = DiameterAct (62.08)
6221 = AccActAdjust (62.21)
Auto
516 = AI2 ValScaled (5.16)
6208 = DiameterAct (62.08)
0
Auto
RelTensRamp
Auto
0
6315 = TensionRef (63.15)
0
6208 = DiameterAct (62.08)
104 = MotSpeed (1.04)
Auto
2024 =IndepTorqMaxSPC (20.24)
6324 = TensToTorq (63.24)
0
Auto
2602 = LoadComp (26.02)
6230 = InertiaComp (62.30)
6334 = FrictionComp (63.34)
Auto
3ADW000379R0307 DCS550 Manual fr c
Préréglages
SpeedRef2301
325 %
-325 %
325 %
-325 %
0 tr/min
1
Speed
TorqSel2601
0 %
5
2500
0
0
-100 %
100 %
0
Auto
Auto
WindCtrlWord
WindCtrlWord
Auto
Auto
0
202 = SpeedRef2 (2.02)
104 = MotSpeed (1.04)
NotUsed
6208 = DiameterAct (62.08)
0
216 = dv_dt (2.16)
6208 = DiameterAct (62.08)
6221 = AccActAdjust (62.21)
Auto
0
6208 = DiameterAct (62.08)
0
Auto
RelTensRamp
Auto
0
6315 = TensionRef (63.15)
0
6208 = DiameterAct (62.08)
104 = MotSpeed (1.04)
Auto
0
6324 = TensToTorq (63.24)
0
Auto
0
6230 = InertiaComp (62.30)
6334 = FrictionComp (63.34)
Auto