Eurosystems MLT 03 Manuel D'utilisation page 31

1. take the gearbox rod away from the
handlebar.
2. unscrew the unblocking lever until the
handlebar support is raised up from the
cutting part shown on the machine.
3. orientate the handlebar support for
180° to the desired job position and
tighten it into the desired central position.
4. tighten the unblocking lever and tighten
the whole again.
5. reinsert the gearbox rod.
If the handlebar is placed on the engine
you can use the cutting bar or the
grassland mower.
If the handlebar is placed behind the
tool you can use the rotavator.
CAUTION!
Making the handlebar rotation for 180°
the gears position are reversed, the ones
forward are reverse and vice versa.
CAUTION!
Cable positioning: please take care to
the cables assembly in order to avoid
problems during the 180° rotation of
the handlebar support. Please look at
the correct positioning as shown in the
picture (1.5, 1.6, 1.7)
BELT AUTO-TENSIONING
10.3
4 . 5 4 . 5
For a correct unit working the
engine belt should always be in traction.
The rear tine tiller is equipped with a pat-
ented belt self-tensioning system which,
when the belt is worn, adjusts its traction
and immediately returns it to its best work-
ing condition.
CAUTION!
The engine belt should be replaced when
between unit cover and engine support
there is about 6 mm space.
Checking the tightness of
fasteners and guards
Cleaning
Inflation
Cable adjustment
Base oil change
Motor
10.4 GEARBOX
4 . 6a 4 . 6a
Use SAE 80 oil. Oil capacity:
1,30 l. To check the oil level: the machine
must be on level ground. Remove filler cap
and check that the oil level is at the bot-
tom of the hole. The filler cap acts also as
the oil level. Check the oil level every 60
work hours.
4 .6 b 4 .6 b
To change the oil: remove
plug and tip the cultivator sideways. The
oil draining should be performed when
the machine is still hot. When the oil has
drained out completely, tip the machine on
the opposite side position and fill it in with
new oil up to the lower level of the hole.
Replace the plug. Change the oil every
150 work hours (with the word "hours",
we mean the machine working hours).
INFORMATION!
Use a syringe (not included) for easier
and safer extraction.
CAUTION!
Use SAE 80 or equivalent oil.
CAUTION!
Waste fuel oil is a polluting material:
don't waste it in the sorroundings, please
apply to suitable waste material centres.
10.5 TYRE INFLATION
If the wheels are not full, we recommend
checking tyre inflation before each ma-
chine use. The recommended value is 21
PSI (1.5 bar).
CAUTION!
Before inflating the tyre, always check
the maximum PSI value on the tyre.
12. MAINTENANCE PLAN
Always before starting the machine - check that there are no untightened
screws, bolts and/or nuts and that the bonnets and protection systems are
intact and correctly fitted.
After each use
As needed
If operation is not as according to the manual
150 hours
See specific manual
Before proceeding, read and under-
stand the chapter "SAFETY INSTRUC-
TIONS" in its entirety.
Wait for all the hot parts to cool down (at
least 20 minutes) before washing and/or
cleaning the machine or the interchange-
able equipment. Use compressed air or a
sponge with neutral detergent and water.
Do not use pressurised water to wash
the machine and/or interchangeable
equipment. Doing so can damage the
motor and any electrical systems or
batteries.
Avoid excessive use of water near la-
bels. In the event of damage, labels
must be replaced before using the
machine and/or the interchangeable
equipment again.
How often
11. CLEANING AND WASHING
DANGER!
CAUTION!
CAUTION!
See chapt.
-
11.
10.5
10.1
10.4