Publicité
Les langues disponibles
Les langues disponibles
DANGER!
Both springs must be correctly en-
gaged for the brake system to function
properly.
DANGER!
If one or both springs break, replace
them before using the machine.
1. 1 0a
1. 1 0a
Tool coupling seat: clean
and grease the seat after each use using
the greasing nipple.
CAUTION!
The motor is supplied without lubricat-
ing oil
1. 12
1. 12
. For information on the
type of oil and quantities to be used, re-
fer to the motor manual contained in the
accessory bag [E].
1. 1
1. 1
7. USE
CAUTION!
Do not start the engine until all assembly
stages have been completed.
CAUTION!
Add lubricating oil to the motor before
first start-up. For information on the type
of oil and quantities to be used, refer to
the motor manual contained in the ac-
cessory bag [E].
1.1
1.1
CAUTION!
Before starting the machine, check the
oil level inside the motor, as indicated in
.
the specific user's manual
DANGER!
Before proceeding, read and understand
the chapter "SAFETY INSTRUCTIONS"
in its entirety.
DANGER!
Check correct functioning of the levers
before using the machine. See the "CA-
BLE ADJUSTMENT" paragraph to make
adjustments.
7.1 DESCRIPTION OF ELEMENTS
SAFETY DEVICE
All rear tine tillers are equipped with an
accident prevention device. Such device
causes the release belt transmission
and the machine to stop on the single or
reverse speed position, and the release of
the control lever; furthermore, such device
avoids the reverse speed engagement if the
single speed is on.
2.2
2.2
NOMENCLATURE
1) Throttle control
2) Forward and reversing lever
3) Pull out/starter handle (self winding
device)
4) Tool control lever
5) Handlebar support unblocking lever
6) Engine
7) Gearbox lever
2.3
2.3
THREE-POSITION WHEEL
CLUTCHING DEVICE: The cultivator is
equipped with a special device called a
"THREE-POSITION FORK".
- In position 1 (free), the wheel turns free-
ly on the shaft so that the machine can
move when the engine is stopped.
DANGER!
Use this position only when the motor
is switched off. Some accessories can
cause injury to imprudent users.
- In position 2 (locked), the wheel is in-
tegral with the shaft, setting into drive,
meaning ready to start working. This is the
most commonly used position.
- In position 3 (semi-differential), the wheel
can perform about a half-turn turning on the
shaft, in order to allow turns.
CAUTION!
All operations on the three-position fork
must be performed when the engine is at
a standstill.
7.2 TANK FILLING
DANGER!
Use caution when handling flammable
fluids. Fuel is highly flammable and ex-
plosive.
DANGER!
Do not fill the tank in closed or poorly
ventilated environments.
DANGER!
Before refilling the tank, switch off the
machine and wait until the motor has
cooled down (15-20 min).
DANGER!
Do
not
smoke
or
use
ic devices near combustible fluids.
DANGER!
Use suitable, undamaged filling devices
such as fuel cans, funnels, etc.
DANGER!
In case of fuel leakage, move the ma-
chine before starting it up.
DANGER!
When filling operations have been com-
pleted, replace the cap and tighten it
firmly.
1.1 3
1.1 3
7.3 START-UP AND SHUT-DOWN
DANGER!
Check correct functioning of the main-
tained action levers and double safety
command before using the machine. See
the "CABLE ADJUSTMENT" paragraph
to make adjustments. It is forbidden to
use the machine in case of malfunction
of the controls.
CAUTION!
At the first use of the machine it is
absolutely necessary to verify that inside
the chassis is present the lubrication oil.
Do no start the unit/machine on before
having done such control. For additional
information please look at the chapter
GEARBOX 10.4.
CAUTION!
When you have finished the assembly,
switch the machine and check, bringing
the accelerator to the stop position, the
engine shuts completely down.
CAUTION!
Before switching the engine on, carefully
check if the motorcultivator is in perfect
good conditions.
1.
Engine instructions: Carefully read
the istructions booklet enclosed to the
relevant engine. Check if the air filter
is clean. Fill the tank in as per the fuel
described in the engine specifications
and using a filter filling funnel. Do not
change the calibration of the speeds
control rotation device of the engine
in order not to over-speed it.
2.3
2.3
2.
Put the fork into position
1 (free) so that the wheel could
freely turn on the shaft to allow the
movements.
electron-
3.
Move the machine to the borders to be
machined.
2.3
2.3
Put the fork into position
4.
2 (blocked) working position. Check
if the gearbox control lever (Fig. 2.2
part 7) is on loose position. Adjust the
handlebar to the requested position/
height.
Publicité
