Maintenance And Cleaning; Transport - Scheppach HM100T Traduction Des Instructions D'origine

Carry out the cut as described in „Chop cutting at
•
90° and rotary table at 0°".
Dust extraction (Fig. 13)
The saw is equipped with an extraction nozzle (46)
•
for extracting dust. By using this, it is easy to attach
the machine to any dust extraction unit.

9. Maintenance and cleaning

m WARNING
Before any adjustment, service or maintenance, dis-
connect the mains supply!
Replacing the saw blade (Fig. 18, 19, 20)
Disconnect the mains; the saw blade must come to
•
a complete standstill.
Set the saw to table mode as described in „Use as
•
table saw".
Loosen the screw (47) on the saw blade guard (37)
•
and lift the saw blade guard (37) from the bracket.
To disassemble the upper saw table (4), loosen
•
two upper screws (48) on the upper saw table (4)
and two lower screws (49). Loosen the screw in the
handle (5) with an Allen key (30).
Lift off the upper saw table.
•
Set the saw to chopping mode as described in „Use
•
as chop and mitre saw".
Using one hand, place the Allen key (29) on the
•
flange screw (50).
Push the saw-shaft lock (6) firmly, and slowly turn
•
the flange screw (50) clockwise. After a maximum
of one turn, the saw-shaft lock (6) clicks into place.
Now using a little more force, loosen the flange
•
screw (50) clockwise.
Unscrew the flange screw (50) completely and re-
•
move the outer flange (51).
Take the saw blade (12) from the inner flange (52)
•
and pull it upwards.
Carefully clean the flange screw (50), the outer
•
flange (51) and inner flange (52).
Insert the new saw blade (12) in reverse order and
•
tighten it.
m WARNING!
The direction of the teeth, i.e. the rotational direc-
•
tion of the saw blade (12) has to correspond with
the direction of the arrow on the casing.
Reassemble the saw table (4) in reverse order and
•
attach the upper saw blade guard (37) again, fixing
it loosely with the screw (47).
Cleaning
Always keep the machine's ventilation slots clear
•
and clean. Regularly remove dust and dirt from the
machine. Cleaning is best with compressed air or
a cloth.
All moveable parts must be lubricated periodically.
•
Do not use corrosive agents for cleaning the plastic.
internet: www.scheppach.com / email: service@scheppach.com / telefon: +(49)-08223-4002-99 / telefax: +(49)-08223-4002- 58 internet: www.scheppach.com / email: service@scheppach.com / telefon: +(49)-08223-4002-99 / telefax: +(49)-08223-4002-58
General maintenance
Every now and then, remove wood chippings and
dust from the machine with a cloth. To increase the
service life of the rotating parts, lubricate them once
a month. Do not lubricate the motor.
Do not use corrosive agents for cleaning the plastic.
Replacing the mains connection
If this machine's mains connection is damaged, it has
to be replaced by the manufacturer, the manufactur-
er's customer service or a similarly qualified agent in
order to prevent hazards.
Carbon brushes
In the event of excessive spark development, have
the carbon brushes checked by an electrician.
m WARNING!
The carbon brushes must be replaced by an electri-
cian.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Carbon brush, saw blade, batteries,
table linings, dust bags, V-belts, sliding stick, push
handle
* Not necessarily included in the scope of delivery!

10. Transport

Transport (always in table saw mode)
Move the lower saw blade guard (14) above the saw
•
guide until you can hear a „click". The front of the
saw blade guard has to be flush with the white line
on the saw guide.
Position the saw button downwards by pressing the
•
unlocking button (2) on the saw head and activating
the lock pin (20).
Put the rip fence (1) on the saw blade guard and
•
attach it.
Lift the machine by holding it on both sides of the
•
lower frame (6).
m WARNING
There is a risk of injury in the event of improper han-
dling of the machine, during lifting or turning.
Always disconnect the mains supply before eve-
ry transport
Only ever transport the saw in table mode and with
the rip fence mounted on the saw blade. This will pre-
vent injury from the saw blade. Never transport the
machine by its safety equipment (e.g. safety guard,
riving knife).
GB
35 І 204