Working With The Machine; Cleaning, Maintenance And Storage - Scheppach PL55Li Traduction Des Instructions D'origine

8. Working with the machine

During work observe all safety instructions provided
previously, as well as the following rules:
• Only guide the electrical tool against the workpiece
when it is switched on.
• Only use the machine if it is functioning correctly.
• If the electrical tool has fallen, check it and the saw
blade for damage. Have damaged parts repaired
before use. Damaged machines can lead to injuries
and machine instability.
• Always secure the workpiece such that it cannot
move during processing.
• Always hold the electrical tool with both hands by
the handles (1) during work. This reduces the risk of
injury and is a precondition for precise work.
• Always slide the saw forwards, never draw it back-
wards towards yourself.
• Avoid the saw blade cutting edge overheating by
working at an appropriate feed speed, and when
cutting plastics also do so to avoid the plastic melt-
ing.
• Wear a mask when carrying out dust-creating work.
Switching on/off
• Slide the switch lock (2) to the ON position and
press the on/off switch (10) (pressed = ON / re-
leased = OFF).
• After the sawing process is complete, slide the
switch lock (2) to the right.
Sawing
1. Place the front part of the machine onto the work
piece.
2. Switch the machine on using the on/off switch..
3. Press the plunge-cut trigger (3).
4. Push the saw downwards to reach the sawing
depth.
5. Push the saw forward evenly.
6. After finishing the sawing cut, switch the machine
off and move the saw blade upwards.
Plunge-cuts (Fig. 5)
1. Place the saw onto the work piece.
2. Place the cutting indicator with the rear arrow (A)
on the marked plunge-cut position.
3. Switch the machine on and push the saw down-
wards until you reach the set cutting depth.
4. Move the saw forwards until the cutting indication
(C) has reached the marked point.
5. After completion of the plunge-cut, move the saw
blade upwards and switch the saw off.
Cutting with rails (otional)
1. Place the machine in the guide rails. can be read-
justed using the hex driver included in the deliv-
ery, when there is the risk of the adjusting screws
releasing by themselves.
22 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
2. Turn on the machine by pressing the on/off switch.
3. Press the dip trigger (3).
4. Press the saw downwards to reach the sawing
depth. During first use the rubber lip is sawn off
and thus splitter protection is guaranteed up to the
saw blade.
5. Push the saw uniformly forwards.
6. Turn off the machine and tilt the saw blade to the
top when the saw cutting is complete.
Sawing with dust suction
Connect the suction hose to the exhaust nozzle - Ø
38 mm (4).

9. Cleaning, maintenance and storage

m Risk of injury, electric shock
• Always remove the rechargeable battery pack from
the electrical tool before performing maintenance
and service work!
• All maintenance and repair work that requires an
opening of the motor housing must be performed
by an authorised customer service workshop.
Cleaning
• Keep the device as free of dust and dirt as possible.
Rub the device clean with a clean cloth or blow it off
with compressed air at low pressure.
• We recommend that you clean the device directly
after every use.
• Clean the device at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the device. Make sure that no water can
penetrate the device interior.
Observe the following information:
• Always keep the cooling air openings in the hous-
ing clean and clear for air circulation.
• Vacuum all openings to remove wooden splinters
and chips from the electrical tool.
• Keep the connection contacts on the electrical tool,
charging unit and rechargeable battery pack clean.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Carbon brushes, saw blade, batteries,
rechargeable batteries
* Not necessarily included in the scope of delivery!