Coffee Dispenser Unit; Cappuccino Dispensing Unit (Bar At Ec); Steam/Hot Water Spout (Bar At Es - Bar At Ec); Installation - La Pavoni BAR AT ES Mode D'emploi

la Pavoni
4 . 3 4 . 3

Coffee dispenser unit

Coffee dispenser unit
4 . 3 4 . 3 4 . 3 Coffee dispenser unit Coffee dispenser unit Coffee dispenser unit
The position of this unit (ref. 21, fig. 4) can be modified accor-
ding to the height of the container used.
In fact it is possible to move the mobile dispenser backwards
(ref. 23, fig. 4) and the telescopic dispenser upwards or
downwards (ref. 24, fig. 4).
This allo ws dif fer ent heights to be obtained.(see fig
N.B.: If a container taller than 90 mm is always and exclusi-
vel y used, the tel e scopi c di s penser can be removed al t ogether
(ref. 23, fig. 4), by drawing it downwards.
fi g .4
4 . 4 4 . 4 Cappuccino dispensing unit Cappuccino dispensing unit
4 . 4 4 . 4 4 . 4 Cappuccino dispensing unit Cappuccino dispensing unit Cappuccino dispensing unit
(BAR AT EC) (BAR AT EC) (BAR AT EC) (BAR AT EC) (BAR AT EC)
8
4
fig. 4a
The cappuccino dispensing unit (fig. 4a) consists of:
- milk supply tube (ref.6, fig. 4a)
- retaining clip for milk supply tube (ref.5, fig. 4a)
- cappuccino device casing (ref.8, fig. 4a)
- pin for regulation of froth quality (ref.2, fig. 4a)
- adjustable dispensing spout (ref.4, fig. 4a)
4 . 5 4 . 5
4 . 5 4 . 5 4 . 5
The steam (r ef. 16, fig . 1) and hot w
are equipped with suitable rubber protectors (ref. 14 and 9,
fig. 1) so that they can be easily gripped and moved even
when over-heated.
. 4).
5 -
21
Operation falling within the competence of the
Maintenance technician
23

5.1 Connections

5.1 Connections 5.1 Connections 5.1 Connections 5.1 Connections
24
The connection will have to be implemented by
observing the national safety rules
Carry out connections as follows:
- Check that the surface upon which the machine is placed
is firm and able to withstand the weight.
- Drill the relevant holes in the surface top (ref. C' and D' or
F', fig. 6), and possibly also the other holes (ref. B', fig. 6 e
ref. E', fig. 6 - see N.B.), as indicated in the drawing.
- Install the machine on the surface and level it by adjusting
the f eet made a vaila ble f or this oper
- Connect machine to the drinking water system by way of
the special fitting (ref. C, fig. 5).
- Connect to the power mains by way of the relevant cord
(ref. D, fig. 5).
N.B.: It is possible to connect the drip tray (ref. 15, fig. 1)
directly to an outlet by proceeding as follows:
- drill the surface top as indicated (ref. B', fig. 6);
- break the removable diaphragm which seals the drip tray
outlet (ref. 15, fig. 1);
- join a drain tube to the fitting (ref. B, fig. 5), by way of a
suitable hose clamp.
2
5
6
A
D
C
E
fig. 5
Steam/hot water spout calda Steam/hot water spout calda
Steam/hot water spout calda Steam/hot water spout calda Steam/hot water spout calda
(BAR AT ES - BAR AT EC) (BAR AT ES - BAR AT EC) (BAR AT ES - BAR AT EC) (BAR AT ES - BAR AT EC) (BAR AT ES - BAR AT EC)
ater spouts (r

INSTALLATION

Danger
Warning
A
A
B
A
Engl i s h
ef. 11, fig . 1)
ation (r ef. A, fig . 5).
35