Machine Switching Off; Disassembling/Assembling The Cover Panels; Setting Out Of Operatione - La Pavoni BAR AT ES Mode D'emploi

Engl i s h
6.20 6.20

Machine switching off

Machine switching off
6.20 6.20 6.20 Machine switching off Machine switching off Machine switching off
Automa ti c pr ogrammed s wi t c hi n g of f
It is possib le w hen the function
(see "6.19.2 Functions description") is active and the program-
ming of "ON/OFF TIME" (see 6.19.2 Functions description)
has also been carried out.
At the pr ogrammed time the mac
Man ual s wi t c hi n g of f
This type of switc hing of f is necessar
MATIC OPERATION" (see "6.19.2 Functions description") is
not acti v ated.
It is obtained by setting both the main switch (ref.
and the multi-pole switch to position "
pl u g.
6.21 6.21 Disassembling/assembling Disassembling/assembling
6.21 6.21 6.21 Disassembling/assembling Disassembling/assembling Disassembling/assembling
the cover panels the cover panels the cover panels the cover panels the cover panels
"CAUTION: To Reduce the Risk of Electric shock or Mechani-
cal Injury, Do Not Remove This Cover. No User Serviceable
Parts Inside. Repair and Cleaning Should Be Done By Autho-
rised Service Personnel Only (Only for USA and CDN mo-
dels)."
The side panels (ref. 1 and 5, fig. 11) and the back panel (ref.
3, fig. 11) can be dismantled for servicing or for customization
that may suit room furniture or wall painting.
Danger
Operation falling within the competence of the
Maintenance technician.
Disconnect the machine from mains by way of main switch
(ref. 10, fig. 1) and all-pole switch, or disconnecting the plug.
Danger of burns
Wait for the machine to cool off sufficiently, before
servicing it.
For parts removal, do the following:
- Pull out the drip tray (ref. 15, fig. 11).
- To unloose the upper screwes (ref. A, fig. 11) of fixing and
to release the lateral panels (ref. 1 and 5, fig. 11).
- Slide glass out (ref. 2, fig. 11).
- Dismantle the cup heating plate (ref. 4, fig. 11) by discon-
necting it from the electronic board, from the earth cable
and from the drain tube (ref. B, fig. 11).
- Unscrew the back panel retaining nuts (ref. 3, fig. 11) and
dismantle it.
To re-assemble one must:
- Assemble the back panel (ref. 3, fig. 11) and secure it with
the relative nuts.
- Assemb le the cup hea ting pla te (r ef. 4, fig . 11) b y inser ting
48
"AUTOMATIC OPERATION"
hine is set on "STANDBY".
y w hen function "AUTO-
10 , fig. 1)
O" or disconnecting the
the electrical connector into the electr
the fitting into the dr ain tube (r ef. B, fig . 11), and b y con-
necting the earth cable.
- Assemb le one of the side panels (or r
fig . 11).
Important
Firstly slide in the bottom pins in their frame slots,
after lock the screw of fixing.
- Position the g lass (r ef. 2, fig . 11) in the slot of
panel already assembled.
- Assemble the other side panel.
- Inser t the drip tr ay into place (r
- Swi t ch machi n e on.
A
4
2
3
1
fig . 11
6.22 6.22

Setting out of operatione

Setting out of operatione
6.22 6.22 6.22 Setting out of operatione Setting out of operatione Setting out of operatione
Danger
Operation falling within the competence of the
Maintenance technician.
When the machine is put out of operation, disconnect both
water and electrical mains; empty all trays, boilers and pipes
and clean the whole machine properly (see "7.2 Machine cle-
ani n g").
In case of scrapping, the various materials used in manufac-
turing will have to be separated and individually disposed of,
according to each Country regulations in force.
la Pavoni
onic boar d pr oper ly,
ef. 1, fig . 11 or r ef. 5,
the la ter al
ef. 15, fig . 11).
5
B
15