REMS Frigo 2 Instructions D'emploi page 7

DEU
zuführen sind, werden kostenlos beseitigt. Durch die Mängelbeseitigung wird
die Garantiezeit für das Produkt weder verlängert noch erneuert. Schäden, die
auf natürliche Abnutzung, unsachgemäße Behandlung oder Missbrauch, Miss-
achtung von Betriebsvorschriften, ungeeignete Betriebsmittel, übermäßige Be-
anspruchung, zweckfremde Verwendung, eigene oder fremde Eingriffe oder
andere Gründe, die REMS nicht zu vertreten hat, zurückzuführen sind, sind
von der Garantie ausgeschlossen.
Garantieleistungen dürfen nur von einer autorisierten REMS Vertrags-Kun-
dendienstwerkstatt erbracht werden. Beanstandungen werden nur anerkannt,
wenn das Produkt ohne vorherige Eingriffe in unzerlegtem Zustand einer au-
torisierten REMS Vertrags-Kundendienstwerkstatt eingereicht wird. Ersetzte
Produkte und Teile gehen in das Eigentum von REMS über.
Die Kosten für die Hin- und Rückfracht trägt der Verwender.
Die gesetzlichen Rechte des Verwenders, insbesondere seine Mängelan-
sprüche gegenüber dem Händler, bleiben unberührt. Diese Hersteller-Garan-
tie gilt nur für Neuprodukte, welche in der Europäischen Union, in Norwegen
oder in der Schweiz gekauft werden.
7. REMS Vertrags-Kundendienstwerkstätten
Firmeneigene Fachwerkstatt für Reparaturen:
SERVICE-CENTER
Schorndorfer Straße 70
D-71332 Waiblingen
Telefon (0 7151) 5 68 08 - 60
Telefax (0 7151) 5 68 08 - 64
Wir holen Ihre Maschinen und Werkzeuge bei Ihnen ab!
Nutzen Sie in der Bundesrepublik Deutschland unseren Abholservice.
Einfach anrufen unter Telefon (0 7151) 5 68 08 - 60.
Oder wenden Sie sich an eine andere autorisierte REMS Vertrags-Kunden-
dienstwerkstatt in Ihrer Nähe.
Basic Safety Instructions
Warning! Read before commissioning!
When using machines, electric tools and electric units – hereinafter referred to
as "units" – basic safety precautions should always be followed to reduce the
risk of electric shock, personal injury and fire, including the following.
Read and comply with all these instructions before operating the unit. Save
these safety instructions.
Only use the unit for the purpose for which it was intended, with due attention
to the general safety and accident prevention regulations.
· Keep work area clean
Cluttered areas invite injuries.
· Consider work area environment
Don't expose units to rain. Don't use in damp or wet locations. Keep work
area well lit. Don't use power tools in presence of flammable liquids or gases.
· Guard against electric shock
Prevent body contact with earthed surfaces (e.g. pipes, radiators, ranges,
refrigerators). If the unit comes with an earthed wire, the plug must only be
connected to an earthed receptacle. At work sites, in the fields or any other
comparable sites of use, the unit shall only be connected to the power supply
with a 30mA fault current protected switch.
· Keep children away
Do not let contact unit or power lead. All bystanders should be kept away
from work area. Only allow trained personnel to use it. Apprentices may
only operate the machine when they are older than 16, when this is necessary
for their training, and under the supervision of a trained operative.
· Store idle units safely
When not in use keep units in a dry place, either locked up or high up, out
of reach of children.
· Never overload a unit
It will do the job better and safer at the rate for which it was intended. Replace
tools in good time.
· Use the right unit for the job
Don't force small units to do the job of a heavy-duty tool. Don't use units for
purposes not intended.
· Dress properly
Do not wear loose clothing or jewellery. They can be caught in moving parts.
Rubber gloves and non-skid footwear are recommended when working
outdoors. Wear protective hair covering to contain long hair.
· Use personal safety equipment
Wear safety goggles. Wear safety glasses. Wear ear defenders to protect
against noise € 85 dB(A). Wear a face mask if work is dusty.
· Don't abuse lead
Never carry unit by lead or yank lead to disconnect from receptacle. Keep
the lead away from heat, oil and sharp edges.
· Secure workpiece
Use clamps or a vice to hold workpiece. It's safer than using your hand and
it frees both hands to operate the unit.
· Don't overreach
Keep proper footing and balance at all times.
· Maintain units with care
Keep tools sharp and clean for better and safer performance. Follow instructions
for servicing and changing tools. Inspect unit leads periodically and, if
damaged, have them repaired by an authorised service facility. Inspect
extension leads periodically and replace them if damaged. Keep handles
dry, clean and free from oil and grease.
· Disconnect units from the power supply
For all operations described under "Preparations for Use" and "Maintenance",
when not in use, before servicing and when changing tools.
· Avoid unintentional starting
Don't carry plugged-in unit with finger on switch trigger. Be sure switch is
turned off when plugging in. Do not bridge the inching switch.
· Outdoor use extension leads
When unit is used outdoors, use only extensions leads intended for use
outdoors and so marked.
· Stay alert
Watch what you are doing. Use common sense. Do not operate unit when
you are tired.
· Check unit for damaged parts
Before further use of the unit, a guard or other part that is damaged should
be carefully checked to determine that it will operate properly and perform
its intended function. Check for alignment of moving parts, binding of moving
GBR