Siemens SINAMICS G130 Manuel page 1013

Tec_ctrl sel bit 0
p2220[C]
(0)
Tec_ctrl sel bit 1
p2221[C]
(0)
Tec_ctrl sel bit 2
p2222[C]
(0)
Tec_ctrl sel bit 3
p2223[C]
(0)
<1> For SERVO and VECTOR is valid:
Further condition: p2216[D] = 2 (factory setting).
<101> The pre-assignment of the sampling time in p0115[6] is 4000.00 μs.
1 2
DO: SERVO, VECTOR, VECTORMV
Technology controller - Fixed value selection binary (r0108.16 = 1)
0.00 %
Tec_ctrl fix val 1
-200.00...200.00 [%]
p2201[D] (10.00)
p2201[D]
Tec_ctrl fix val 2
-200.00...200.00 [%]
p2202[D] (20.00)
p2202[D]
Tec_ctrl fix val 3
-200.00...200.00 [%]
p2203[D] (30.00)
p2203[D]
Tec_ctrl fix val 4
-200.00...200.00 [%]
p2204[D] (40.00)
p2204[D]
Tec_ctrl fix val 5
-200.00...200.00 [%]
p2205[D] (50.00)
p2205[D]
Tec_ctrl fix val 6
-200.00...200.00 [%]
p2206[D] (60.00)
p2206[D]
Tec_ctrl fix val 7
-200.00...200.00 [%]
p2207[D] (70.00)
p2207[D]
Tec_ctrl fix val 8
-200.00...200.00 [%]
p2208[D] (80.00)
p2208[D]
Tec_ctrl fix val 9
-200.00...200.00 [%]
p2209[D] (90.00)
p2209[D]
Tec_ctrl fix val 10
-200.00...200.00 [%]
p2210[D] (100.00)
p2210[D]
Tec_ctrl fix val 11
-200.00...200.00 [%]
p2211[D] (110.00)
p2211[D]
Tec_ctrl fix val 12
-200.00...200.00 [%]
p2212[D] (120.00)
p2212[D]
Tec_ctrl fix val 13
-200.00...200.00 [%]
p2213[D] (130.00)
p2213[D]
Tec_ctrl fix val 14
-200.00...200.00 [%]
p2214[D] (140.00)
p2214[D]
Tec_ctrl fix val 15
-200.00...200.00 [%]
p2215[D] (150.00)
p2215[D]
3 4
3 0
2 2 0 ... 15
Tec_ctrl No act
0 0 0 0
<1>
r2229
0 0 0 1
0 0 1 0
0 0 1 1
0 1 0 0
0 1 0 1
0 1 1 0
0 1 1 1
1 0 0 0
1 0 0 1
1 0 1 0
1 0 1 1
1 1 0 0
1 1 0 1
1 1 1 0
1 1 1 1
5 6
fp_7950_51_eng.vsd
06.11.09 V04.03.01
p0115[6] (Drive Object)
Refer to [1020.7]
<101>
Tec_ctr FixVal sel
r2225.0
Tec_ctr FixVal eff
r2224
7 8
Function diagram
- 7950 -
SINAMICS