Transportation And Storage - Ryobi Expand-It RXPR01 Traduction Des Instructions Originales

■
Inspect the product before each use. Check for loose
fasteners. Make sure all guards and handles are
properly and securely attached. Replace any damaged
parts before use.
■
Do not modify the product in any way.
■
Do not allow children or untrained individuals to use the
product.
■
Wear full eye and hearing protection while operating the
product. If working in an area where there is a risk of
falling objects, head protection must be worn.
■
Wear heavy long trousers, boots, and gloves. Do not
wear loose fitting clothing, short trousers, jewellery of
any kind, or use with bare feet.
■
Secure long hair so it is above shoulder level to prevent
entanglement in moving parts.
■
Use of hearing protection reduces the ability to hear
warnings (shouts or alarms). The operator must pay
extra attention to what is going on in the working area.
■
Operating similar tools nearby increases both the risk
of hearing injury and the potential for other persons to
enter your working area.
■
Do not use this machine when you are tired, ill, or under
the influence of alcohol, drugs, or medication.
■
Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance and can
result in serious injury, or exposure to hot surfaces.
■
Keep all parts of your body away from any moving part.
■
Before starting the product, make sure the cutting
blades will not come in contact with anything.
■
Never operate the product in an explosive atmosphere.
■
While operating the product, always hold it firmly with
both hands by the two handles and ensure that the
operating position is safe and secure. The manufacturer
does not recommend the use of steps or ladders.
■
Use the harness if it is supplied with your hedge
trimmer. It will assist you to support the weight of the
product during use and while moving between trimming
positions. Carefully adjust the harness to fit comfortably.
■
Identify the quick release mechanism and practice
using it before you start using the product. Its correct
use may prevent serious injury in the case of an
emergency. Never wear additional clothing over
the harness or otherwise restrict access to the quick
release mechanism.
■
To protect yourself from electrocution, do not operate
within 10 m of overhead electrical lines.
■
Never use the product near fencing, posts, buildings, or
other immovable objects.
■
Blades are sharp. When handling the blade assembly,
wear non-slip, heavy-duty protective gloves. Do not
place your hand or fingers between blades or in any
position where they could get pinched or cut.
■
Always stop the product, disconnect from the power
supply (if applicable), make sure all moving parts have
come to stop, and allow the hedge trimmer to cool down
before:
●
adjusting the working position of the cutting device;
●
cleaning or clearing a blockage;
●
leaving the product unattended;
●
checking, maintaining, or working on the product.
■
Do not force the product through heavy shrubbery. This
can cause the blades to bind and slow down. If the
blades slow down, reduce the pace.
■
Do not attempt to cut stems or twigs that are larger
than 28 mm thick, or those obviously too large to feed
into the cutting blade. Use a non-powered hand saw or
pruning saw to trim large stems.
■
Do not operate the product with damaged or excessively
worn blades.
WARNING
If the product is dropped, suffers heavy impact, or begins
to vibrate abnormally, immediately stop the product and
inspect for damage or identify the cause of the vibration.
Any damage should be properly repaired or replaced by
an authorised service centre.
WARNING
Check that all the shaft couplings on the extension shaft
and tool are securely fastened before each use and at
frequent intervals.
ADDITIONAL SAFETY WARNINGS FOR ASSEMBLING
WITH ELECTRIC-DRIVEN POWER HEAD
■
Electrical power should be supplied via a residual
current device (RCD) with a tripping current of not more
than 30 mA.
■
If you need to use an extension cable, ensure it is
suitable for outdoor use and has a current capacity
sufficient to supply your product. Check it before every
use for damage. Always uncoil it during use because
coiled cables can overheat.
■
If the power cable becomes damaged, it must be
replaced before using.

TRANSPORTATION AND STORAGE

FOR ASSEMBLING WITH PETROL-DRIVEN POWER
HEAD
■
Stop the engine and allow it to cool before storing or
transporting.
■
Clean all foreign material from the product.
■
Cover the blade with the blade protector before storing
the product or during transportation.
■
Drain all fuel from the tank into a container approved
for petrol. Remember to properly replace and tighten
the fuel cap.
■
If applicable, drain all lubricant from tank into a
container approved for lubricant. Remember to properly
replace the lubricant cap.
■
Run the engine until it stops, this will remove all fuel
that could become stale and leave varnish and gum in
the fuel system.
■
Store the product in a cool dry and well-ventilated
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
English | 3