Denon ADV-700 Mode D'emploi page 46

ENGLISH
23 TROUBLESHOOTING
Check again before assuming the player is malfunctioning
Are all the connections correct ?
2
Are you following the instructions in the manual ?
2
Are the speakers and other components operating properly ?
2
If this unit does not seem to be functioning properly, check the table below. If this does not solve the problem, this unit may be
damaged. Turn off the power, unplug the power cord from the power outlet, and contact your store of purchase or nearest Denon
sales office.
Symptom
DISPLAY not lit and sound not • Power cord not plugged in securely.
produced when power switch set to
on.
• Speaker cords not securely connected.
• Improper position of the audio function
button.
DISPLAY lit but sound not produced. • Volume control set to minimum.
• MUTING is on.
• Digital signals not input Digital input
selected.
• Connections between the video output
jack of this unit and the input connector
of the monitor are incomplete.
• The input setting of the monitor TV is
Monitor doesn't display an image.
different.
• The video signals of the various devices
are not uniform.
The program cannot be copied from • Almost all movie software contains a
DVD to the VCR. copy prevention signal.
• Power is not being supplied to the
subwoofer.
The subwoofer does not produce • The subwoofer setting is made to "No"
sound. in the setup.
• The output of the subwoofer has not
been connected.
• The surround mode is set to a mode
The test tone is not output.
other than auto decode.
• Batteries dead.
• Remote control unit too far from this
unit.
• Obstacle between this unit and remote
control unit.
This unit does not operate properly • Different button is being pressed.
when remote control unit is used. • < and > ends of battery inserted in
reverse.
• The mode selection of the remote
control is not properly selected. The
DVD mode, AV mode, or audio mode is
not properly selected.
46
All manuals and user guides at all-guides.com
Cause Measures
• Check the insertion of the power cord
plug.
• Connect securely.
• Set to a suitable position.
• Turn volume up to suitable level.
• Switch off MUTING.
• Input digital signals or select input jacks
to which digital signals are being input.
• Check whether the connections are
correct.
• Set the input switching of the TV to the
jack to which the video input is
connected.
• Make settings uniform for either
composite video or S-video connectors.
• A copy cannot be made.
• Switch on the power of the subwoofer.
• Change the setting to "Subwoofer" in
the setup.
• Make the proper connections.
• Set to auto decode.
• Replace with new batteries.
• Move closer.
• Remove obstacle.
• Press the proper button.
• Insert batteries properly.
• Press the remote control mode
selection button for the item you wish
to operate. To operate this unit, use
with the DVD mode.
Symptom
Playback does not start when PLAY
button is pressed.
Playback stops immediately.
Menu playback of video CD's is not
possible.
Picture is disturbed during the search
operation.
Page
Buttons do not operate.
5
No subtitles are displayed.
8
19
Audio (or subtitle) language does not
switch.
19
20
19
Angle does not switch.
Playback does not start when the
6, 7
title is selected.
—
The password for rating level has
been forgotten.
6, 7
Reset all the DVD setting to
Factory Preset.
—
The disc is not played with the audio
or subtitle language set as the
default setting.
—
Picture is not displayed in 4:3 (or
16:9).
14
8 Menu screen messages for the
desired language do not display.
22
10
10
10
9
10
9
Check
• Is there condensation on the disc or player ? (Let stand for 1 or 2 hours.)
• Discs other than DVDs, video CDs and music CDs cannot be played.
• Disc is dirty. Wipe off the dirt.
• Menu playback is not possible with anything but video CDs with playback control.
• Some disturbance is normal.
• Some operations are disabled for some discs.
• Subtitles are not displayed for DVDs not containing subtitles.
• Subtitles are turned off. Turn the subtitles setting on.
• The audio (or subtitle) language does not switch for discs which do not include multiple
audio (or subtitle) languages.
• For some discs the audio (or subtitle) language cannot be switched when the operation
to switch it is performed, but can be switched on the menu screens.
• The angle cannot be switched for DVDs which do not contain multiple angles. In some
cases multiple angles are only recorded for specific scenes.
• Check the "RATINGS SETUP" setting.
• While the player is in the stop mode, hold the player's SKIP (
8
PAUSE (3 ) button down simultaneously for longer than 3 seconds (until "INITIALIZE"
disappears from the TV monitor).
The lock will be released and the DVD all default settings and picture settings will return
to the default values.
• The disc does not play with the selected audio or subtitle language if that audio or
subtitle language is not included on that DVD.
• Set the "TV ASPECT" default setting to the proper setting for the connected TV.
• Check the default setting for the disc language's menu language.
Page
—
4
5
—
—
18
—
40, 41
35
37
36
44
) button and the 44
35
42
40, 41