Denon ADV-700 Mode D'emploi page 20

ENGLISH
After starting playback
[1] Adjusting the sound quality (SDB / TONE)
The SDB/TONE function will not work in the direct mode.
2
POWER
VCR POWER
c 8 1:02:46
TV POWER
1
DVD TONE
2
2
ENTER
MODE
VOLUME
BAND
MUTE
CH SHIFT
NTSC/PAL STATUS
TU MEMO
SUB TITLE ANGLE TOP MENU
AUDIO
RDS PTY CT RT
PROG/DIRECT REPEAT A-B REPEAT RANDOM
CH.SELECT T.TONE SDB/TONE SURR.PARA
1
SETUP CDR/MD/TAPE TUNER/TV/VCR DVD
1 Press the SDB/TONE button.
• The tone switches as follows each time the
SDB/TONE button is pressed.
SDB/TONE SDB/TONE
Main unit Remote control unit
DEFEAT SDB BASS
(ON/OFF)
2 With the name of the volume to be adjusted selected,
turn the FUNCTION/SELECT knob or cursor button (
, ) to adjust the level.
FUNCTION
/SELECT
Main unit Remote control unit
DEFEAT
• The signals do not pass through the SDB, bass and
treble adjustment circuits, providing higher quality
sound.
SDB
• Either turn the FUNCTION / SELECT dial or use the
( , ) cursor buttons to select "ON" or "OFF".
BASS, TREBLE
• To increase the bass or treble: Turn the control
clockwise or press the cursor button. (The bass or
treble sound can be increased to up to +10 dB in
steps of 2 dB.)
• To decrease the bass or treble: Turn the control
clockwise or press the cursor button. (The bass or
treble sound can be decreased to up to –10 dB in
steps of 2 dB.)
If no operation is performed within 4 seconds, the
display switches back to what was previously
displayed.
20
All manuals and user guides at all-guides.com
POWER
VCR POWER
TV POWER
[2] Turning the sound off temporarily (MUTING)
1
MODE
VOLUME
BAND
MUTE
CH SHIFT
NTSC/PAL STATUS
TU MEMO
SUB TITLE ANGLE TOP MENU
AUDIO
RDS PTY CT
PROG/DIRECT REPEAT A-B REPEAT RANDOM
CH.SELECT T.TONE SDB/TONE SURR.PARA
SETUP CDR/MD/TAPE TUNER/TV/VCR DVD
REMOCON MODE
1 Use this to turn off the audio output temporarily.
Press the MUTE button.
Cancelling MUTE mode.
Press the MUTE button again.
NOTE:
• The setting is cancelled if the set's power is turned off.
[3] Listening over head phones
TREBLE
c 8 1:02:46
1
DVD TONE
1
1 Connect the headphones to the PHONES jack of the
front panel.
The output to the speaker automatically is turned
off and no sound is produced from the speakers.
PHONES
13 DOLBY / DTS SURROUND
Surround
This unit is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the
same sense of presence as in a movie theater.
Dolby Surround
1
(1) Dolby Digital (Dolby Surround AC-3)
Dolby Digital is the multi-channel digital signal format developed by Dolby Laboratories.
Dolby Digital consists of up to "5.1" channels - front left, front right, center, surround left, surround right, and an additional
RT
channel exclusively reserved for additional deep bass sound effects (the Low Frequency Effects – LFE – channel, also called
the ".1" channel, containing bass frequencies of up to 120 Hz).
Unlike the analog Dolby Pro Logic format, Dolby Digital's main channels can all contain full range sound information, from the
lowest bass, up to the highest frequencies – 22 kHz. The signals within each channel are distinct from the others, allowing
pinpoint sound imaging, and Dolby Digital offers tremendous dynamic range from the most powerful sound effects to the
quietest, softest sounds, free from noise and distortion.
2 Dolby Digital and Dolby Pro Logic
Comparison of home surround
systems
MUTE
No. recorded channels (elements)
No. playback channels
Playback channels (max.)
Remote control unit
Audio processing
High frequency playback limit of
surround channel
2 Dolby Digital compatible media and playback methods
Marks indicating Dolby Digital compatibility:
The following are general examples. Also refer to the player's operating instructions.
Media
LD (VDP)
DVD
Others
(satellite broadcasts, CATV, etc.)
1 Use a commercially available adapter to connect Dolby Digital RF (AC-3RF) output signals to the digital input terminals.
(Refer to the adapter's operating instructions.)
Please refer to the instruction manual of the adapter when making connection.
2 To play in Dolby Digital Surround on the ADV-700, set "DVD setting change" – "Audio setting" – "Digital output" to
"Normal" in the setup. (The factory default is "Normal".)
Dolby Digital
5.1 ch
5.1 ch
L, R, C, SL, SR, SW L, R, C, S (SW - recommended)
Digital discrete processing Dolby Digital (AC-3) Analog matrix processing Dolby
encoding/decoding Surround
20 kHz
and .
Dolby Digital output jacks Playback method (reference page)
Coaxial Dolby Digital RF output jack Set the input mode to "AUTO".
1
Optical or coaxial digital output
Set the input mode to "AUTO".
(same as for PCM)
2
Optical or coaxial digital output Set the input mode to "AUTO".
(same as for PCM)
Dolby Pro Logic
2 ch
4 ch
7 kHz
(Page 19)
(Page 19)
(Page 19)