Denon ADV-700 Mode D'emploi page 26

ENGLISH
15 DSP SURROUND SIMULATION
(1) Surround modes and their features
• This unit is equipped with a high performance DSP (Digital Signal Processor) which uses digital signal processing to synthetically
recreate the sound field. One of 7 preset surround modes can be selected according to the program source and the parameters
can be adjusted according to the conditions in the listening room to achieve a more realistic, powerful sound. These surround
modes can also be used for program sources not recorded in Dolby Surround Pro Logic or Dolby Digital.
In this mode, the signals of the front left channel are output from the left surround channel, the signals
of the front right channel are output from the right surround channel, and the same (in-phase) component
1 5CH STEREO
of the left and right channels is output from the center channel. This mode provides all speaker surround
sound, but without directional steering effects, and works with any stereo program source.
MONO MOVIE
Select this when watching monaural movies for a greater sense of expansion.
2
(NOTE 1)
Use this mode to achieve the feeling of a live concert in an arena with reflected sounds coming from all
3 ROCK ARENA
directions.
This mode creates the sound field of a live house with a low ceiling and hard walls. This mode gives jazz
4 JAZZ CLUB
a very vivid realism.
5 VIDEO GAME Use this to enjoy video game sources.
Select this to emphasize the sense of expansion for music sources recorded in stereo. Signals consisting
6 MATRIX of the difference component of the input signals (the component that provides the sense of expansion)
processed for delay are output from the surround channel.
7 VIRTUAL Select this mode to enjoy a virtual sound field, produced from the front 2-channel speakers.
Depending on the program source being played, the effect may not be very noticeable.
In this case, try other surround modes, without worrying about their names, to create a sound field suited to your tastes.
NOTE 1: When playing sources recorded in monaural, the sound will be one-sided if signals are only input to one channel (left or
right), so input signals to both channels. If you have a source component with only one audio output (monophonic
camcorder, etc.) obtain a "Y" adaptor cable to split the mono output to two outputs, and connect to the L and R inputs.
NOTES:
• Only the AUTO DECODE (Auto stereo), DIRECT and STEREO modes can be used when playing PCM signals with a sampling
frequency of 96 kHz (such as from DVD-Video discs that contain 24 bit, 96 kHz audio). If such signals are input during playback
in one of the other surround modes, the mode automatically switches to AUTO DECODE (Auto stereo).
• When DTS signals are input while playing in the virtual surround mode, the surround mode is automatically set to "STEREO".
Personal Memory Plus
This set is equipped with a personal memorize function that automatically memorizes the surround modes and input modes
selected for the input different sources. When the input source is switched, the modes set for that source last time it was
used are automatically recalled.
• Settings automatically stored in the memory for the individual input functions using the Personal Memory Plus function:
q Surround mode (including 2-channel decode mode and Dolby Pro Logic II mode settings)
w Input mode selection function
The surround parameters, SDB/tone control settings and playback level balance for the different output channels are
memorized for each surround mode.
26
All manuals and user guides at all-guides.com
(2) DSP Surround simulation
1
2
SURROUND
MODE
Main unit
3
3 2
c 8 1:02:46
1
DVD TONE
1,2
CH
ON 1 2 3
POWER POWER CH VCR
OFF 4 5 6
VCR POWER VCR POWER CH VOL
CLEAR 7 8 9
TV
TV POWER TV POWER CH TV/VCR SLEEP
CALL +10 0
DISPLAY RETURN INPUT MODE SURROUND
2
MENU
FUNCTION
1
5 5
ENTER
MODE
VOLUME
BAND
MUTE
CH SHIFT
NTSC/PAL STATUS
TU MEMO
SUB TITLE AUDIO ANGLE TOP MENU
RDS PTY CT RT
PROG/DIRECT REPEAT A-B REPEAT RANDOM
CH.SELECT T.TONE SDB/TONE SURR.PARA
4
SETUP CDR/MD/TAPE TUNER/TV/VCR DVD
REMOCON MODE
Select the input source.
FUNCTION
FUNCTION
/SELECT
Main unit Remote control unit
Select the surround mode for the input channel.
FUNCTION
SURROUND
/SELECT
\
Main unit Remote control unit
• The surround mode switches in the following order
each time the SURROUND MODE button is pressed:
STEREO AUTO DECODE 5CH STEREO MONO MOVIE
ROCK ARENA JAZZ CLUB VIDEO GAME
...
MATRIX VIRTUAL DIRECT STEREO
Play a program source.
• Refer to instruction manual for handling.
4
To enter the surround parameter
SURR.PARA
setting mode, press the
SURROUND mode.
• The surround parameter
switches in the following order
each time the SURROUND
Remote control unit
button is pressed for the
different surround modes.
MONO MOVIE
ROCK ARENA
JAZZ CLUB
VIDEO GAME MATRIX VIRTUAL
ROOM SIZE DELAY EFFECT
EFFECT DEFAULT DEFAULT
DEFAULT
There is no 5-channel stereo mode.
Refer to page 27 for the parameters of the "AUTO
DECODE" mode.
5
Display the parameter you want to adjust,
• Use the cursor buttons ( , ) to select the
surround parameter.
Remote control unit
• ROOM SIZE setting
R.SIZE MED
SMALL MED-S MED MED-L LARGE
, /
• EFFECT LEVEL setting
EFFECT 10
1 10 15
, /
• DELAY TIME setting
DELAY 30ms
0ms 30ms 110ms
, /