Operating Times; Symbols Machine; Symbols Operating Instructions; Normal Intended Use - ATIKA BWS 500 Notice Originale - Consignes De Sécurité - Pièces De Rechange

Operating times

Before initiating the device please observe the provisions pertaining to
corresponding laws (regional provisions) for the noise control.

Symbols machine

Carefully read opera-tor's
manual and the safety
instructions
starting the machine and
observe the instructions
when operating.
Risk of injuries of fin-gers
and hands by the saw
blade
Wear eye and
protection
Wear a face mask.
Direction of saw blade rotation
This product complies with European regulations specifically
applicable to it.
Electrical devices do not go into the domestic rubbish. Give
devices, accessories and packaging to an eco-friendly
recycling.
According to the European Directive 2012/19/EU on electrical and
electronic scrap, electrical devices that are no longer serviceable must be
separately collected and brought to a facility for an environmentally
compatible recycling.

Symbols operating instructions

Threatened hazard or hazardous situation. Not observing this
instruction can lead to injuries or cause damage to property.
Important information on proper handling. Not observing this
instruction can lead to faults.
User information. This information helps you to use all the
functions optimally.
Assembly, operation and servicing. Here you are explained
exactly what to do.
Please refer to the attached assembly and
,
operating instruction sheet for references to
,
figure numbers in the text.
,
...

Normal intended use

This machine is designed for cross cutting firewood in the house and
hobby field.
Cutting round material having a diameter over 18 cm is not allowed as
these pieces can not be held safely.
Cutting round material having a diameter smaller than 30 mm or greater
than 180 mm is not allowed as these pieces can not be held safely.
11
Shut off engine and
remove power cord
be-fore before
cleaning,
maintenance
repair work.
Wear
gloves!
ear Wear safety shoes
Warning of hot sur-
faces. Danger of bur-
ning!
Do not touch hot engine parts.
The length of the material to be cut must not exceed 1000 mm. The
length of the material must be 200 mm as a minimum.
Only high-quality saw blades acc. to EN 847-1 up to a max. diameter of
500 mm must be used.
Because it has no extraction device this machine must only be used
outdoors.
Only work pieces are allowed to be processed which can be safely placed
and held in the jigging device.
The use of saw blades made of HSS steel (high-alloy high speed steel) is
not permitted since this steel is hard and brittle. Risk of injury through saw
blade breakage and expulsion of saw blade pieces.
performing
The intended usage also includes compliance with the operating,
servicing and repair conditions prescribed by the manufacturer and
or
following the safety instructions included in the instructions.
The relevant accident prevention regulations for the operation as well as
the other generally acknowledged occupational medicine and safety rules
protective
must be complied with.
Any other use is deemed not to be intended use. The manufacturer is not
liable for any type of damage resulting from this: the user bears the sole
risk.
Unauthorized modifications to the saw preclude any liability of the
manufacturer for resulting damages of any kind.
The saw may only be equipped, used and serviced by persons who are
familiar with it and have been instructed on the hazards. Repair works
may only be carried out by us or by a customer service agent nominated
by us.
The machine may not be used in a potentially explosive environment or
be exposed to rain.
Metallic parts (wires etc.) have unconditionally to be removed from the
material to be cut.

Risidual risks

Even if used properly, residual risks can exist even if the relevant safety
regulations are complied with due to the design determined by the intended
purpose.
Residual risks can be minimised if the "Safety instructions" and the "Normal
intended use" as well as the whole of the operating instructions are observed.
Observing these instructions, and taking proper care, will reduce the risk of
personal injury or damage to the equipment.
Danger of injury of fingers and hands by the tool (saw blade) or work
piece, e.g. when replacing the saw blade.
Injury by catapulted workpiece parts.
Throwback of the workpiece or workpiece parts.
Breaking or catapulting of saw blade.
Risk from electricity, by using non-standard electrical connections.
Touching live parts of opened electrical components.
Impairment of hearing when working on the machine for longer periods of
time without ear protection.
Emission of harmful wood dusts. Wear therefore a protective mask.
Noise emission: Use saw blades designed for noise reduction and keep
the machine in a good condition.
In addition, in spite of all the precautionary measures taken, non-obvious
residual risks can still exist.

Safe working

Woodworking machines can be dangerous if not used properly. If
electrical tools are used, the fundamental safety precautions must be
met to preclude the risks of fire, electric shock and injuries to persons.
Before starting this device, read and keep to the following advice. Also
observe the preventive regulations of your professional association and
the safety provisions applicable in the respective country, in order to
protect yourself and others from possible injury.
Pass the safety instructions on to all persons who work with the
machine.
Keep these safety instructions in a safe place.