Schinkelstraße 97; Declaration Of Conformity; Extent Of Delivery; Characteristics Noise Values - ATIKA BTU 450 Notice Originale
Masquer les pouces
Voir aussi pour BTU 450:
- Instructions de montage (28 pages) ,
- Instructions de montage (34 pages)
Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Do not operate machine before having read the
operating instructions, understood all the notes and
assembly the machine as described here.
Keep the instructions in a safe place for future use.
Contents
-
-
EC Declaration of Conformity
according to EC directive 2006/42/EC
We,
59227 Ahlen - Germany
herewith declare under our sole responsibility that the product
Baukreissäge (construction circular saw) type BTU 450
Serial number: see last page
is conform with the above mentioned EC directives as well as with the
provisions of the guidelines below:
2004/108/EC, 2000/14/EC and 2006/95/EC
Following harmonized standards have been applied:
EN 60204-1:2006; EN 1870-1:2007+A1:2009; EN 55014-1:2006;
EN 55014-2:1997+A1; EN 61000-3-2:2006: EN 61000-3-11:2000
Conformity assessment procedure: 2000/14/EC - Appendix V
Measured level of the acoustic output L
Guaranteed level of the acoustic output L
EC type examination carried out by :
Fachausschuss Holz - Vollmoellerstraße 11 - 70563 Stuttgart - Nr.: 0392
Certificate no.: HO 101119
Keeping of technical documents at:
ATIKA GmbH & Co. KG - Technical department - Schinkelstr. 97
59227 Ahlen - Germany
Ahlen, 21.05.2010
11
= 106,3 dB(A)
WA
= 110 dB(A)
WA
A. Pollmeier, management
Extent of delivery
1 Construction circular saw
•
•
1 Parallel limit stop
•
1 Pushstick
•
Assembly accessories for saw blade change
•
Operating manual
Check the machine for:
11
That it is complete
11
Check for possible transport damage
11
Report any damage or missing items to your dealer, supplier or the
11
manufacturer immediately. Complaints made at a later date will not be
11
acknowledged.
12
12
Characteristics noise values
12
12
EN ISO 3744:1995 / EN ISO 11202:1995/AC:1997 /
13
ISO 7960:1995 Appendix A, A.2 b)
14
Application of the machine as construction circular saw with standard saw
blade.
15
Guaranteed sound power level L
16
Sound pressure level at the workplace
16
17
17
The factor of measurement uncertainty is K = 4 dB.
17
The values given are emission values and must therefore not simultaneously
17
represent safe workplace values too. Although there is a relationship between
emission and immersion levels, it can be reliably deduced whether additional
18
precautionary measures are necessary or not. Factors, which can influence the
18
immersion level currently existing at the workplace include the duration of the
19
effects, the special type of the workroom, other noise sources, etc. e.g. the
number of machines and other adjacent processes. The permissible workplace
values can also vary from country to country. This information should however
enable an improved assessment of the danger and risk to be carried out.
Operating times
Before initiating the device please observe the provisions pertaining to
corresponding laws (regional provisions) for the noise control.
Symbols machine
Carefully read opera-
tor's manual and the
safety instructions be-
fore starting the machine
and observe the
instructions when
operating.
Wear ear protection!
Electrical devices do not go into the domestic rubbish. Give
devices, accessories and packaging to an eco-friendly recycling.
According to the European Directive 2002/96/EC on electrical
and electronic scrap, electrical devices that are no longer
serviceable must be separately collected and brought to a facility
for an environmentally compatible recycling.
= 110 dB(A)
WA
No-load L
= 86,6 dB(A)
PA
Load L
= 94,5 dB(A)
PA
Shut off engine and
remove power cord
before performing
cleaning, maintenance or
repair work.
Publicité
Chapitres
Table des Matières
