Storage; Electrical Connection - Scheppach HS111 Traduction Des Instructions D'origine

14.4.3 Removing the saw blade guard (fig. 25, 26)
PREREQUISITE: The saw blade (7) has been set to
the maximum cutting depth (see 10.2).
1. Place the open-ended spanner 22 mm (f) on the
outer saw blade flange (7b) and secure the drive
shaft (7c) in this way.
2. Turn the fixing nut (7d) counterclockwise with the
open-ended spanner 22 mm (f) to undo the fixing
nut (7d).
3. Hold the saw blade (7) carefully with one hand.
4. Remove the fixing nut (7d) and outer saw blade
flange (7b) from the drive shaft (7c).
5. Now remove the saw blade (7) from the drive shaft
(7c) and carefully draw it up and out of the saw
table (2).
ATTENTION
Also remove the reducing ring (7e) located on the
shaft.
14.4.4 Fitting the saw blade (fig. 26)
1. Clean the outer and inner saw blade flange (7a/7b)
carefully, before fitting a new saw blade (7).
2. Clean the reducing ring (7e) and insert it again.
3. Place a new saw blade (7) on the drive shaft (7c).
Observe the rotational direction: The cutting an-
gle of the teeth must point in the running direction
(forwards). The running direction is usually also
marked on the saw blade.
4. Fit the outer saw blade flange (7b) back on the
drive shaft (7c). Ensure the correct alignment of
the outer saw blade flange (7b).
5. Screw the fixing nut (7d) tight onto the drive shaft
(7c) with the hand.
6. Carefully turn the saw blade (7) in the running di-
rection: It must be precisely centred and must not
"wobble". Check that the saw blade (7) and the
outer saw blade flange (7b) are correctly seated.
Re-align the parts if the saw blade is not exactly
centred.
m WARNING
Warning against unexpected hazards and damag-
es to the product
- Check the setting of the saw blade after every
saw blade replacement.
7. Hold the outer saw blade flange (7b) in place with
the 22 mm open end spanner (f).
8. Tighten the fixing nut (7d) clockwise with the 22
mm spanner (f).
9. Mount the table inlay (5) and the saw blade guard
(8) (see 8.3.3 and 8.4.1).
10. Check the correct setting of the riving knife (see
8.3.2).
14.5 Service information
With this product, it is necessary to note that the fol-
lowing parts are subject to natural or usage-related
wear, or that the following parts are required as con-
sumables.
Wearing parts*:Carbon brushes, table inlay, push
stick, saw blade
* may not be included in the scope of supply!

15. Storage

m WARNING
Danger of injury due to unexpected start-up of the ma-
chine
- Pull the mains plug out of the outlet.
ATTENTION
Product damage due to incorrect storage
- Store the product protected against dirt, dust and
moisture.
- Store the product in its original packaging.
1. Store the product in a dark, dry and frost-free
place that is inaccessible to unauthorised persons.
2. The optimum storage temperature lies between 5
and 30 °C.
3. Store the operating manual with the product.

16. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions. The
customer's mains connection as well as the ex-
tension cables used must also comply with these
regulations.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection conditions.
This means that use of the product at any freely se-
lectable connection point is not allowed.▪Given un-
favorable conditions in the power supply the prod-
uct can cause the voltage to fluctuate temporarily.
• The product is intended solely for use at connec-
tion points that
a. do not exceed a maximum permitted supply im-
pedance "Zmax = 0.345 Ω", or
b. have a continuous current-carrying capacity of
the mains of at least 100 A per phase.
• As the user, you are required to ensure, in consulta-
tion with your electric power company if necessary,
that the connection point at which you wish to oper-
ate the product meets one of the two requirements,
a) or b), named above.
www.scheppach.com
GB | 43