Scheppach HS111 Traduction Des Instructions D'origine page 37

8.1.1 Pre-mounting the legs of the base frame
(fig. 4)
1. Turn the saw table (2) over and place it on the
floor.
2. Fit the four legs (18) into the recesses of the ma-
chine housing.
8.1.2 Fitting table width extensions and table
extensions (fig. 4)
1. Insert the rail connectors (A) into the guide rail (28)
of the table extensions (10).
2. Mount both table width extensions (10) loosely
on the saw table (2) with a total of four hexagon
screws M6×12, four washers and fours nuts M6
(a). To do so, use the corresponding holes drilled
into the saw table (2).
3. Mount the table extension (3) loosely on the saw
table (2) with a total of three hexagon screws
M6×12, three washers and three nuts M6 (a). To
do so, use the corresponding holes drilled into the
saw table (2).
8.1.3 Fitting the table supports (fig. 5)
1. Mount both short table supports (25) loosely on
the right table width extension (10b) with a total of
two hexagon screws M6×12, two washers and two
nuts M6 (a). Mount the table supports (25) loosely
on the machine housing with two hexagon screws
M6x30 and two washers (b), as shown.
2. Mount both medium table supports (24) loosely on
the left table width extension (10a) with two hexa-
gon screws M6×12, two washers and two nuts M6
(a). Mount the table supports (24) loosely on the
machine housing with two hexagon screws M6x30
and two washers (b), as shown.
3. Mount both long table supports (23) loosely on
the table extension (3) with a total of two hexa-
gon screws M6×12, two washers and two nuts M6
(a). Mount the table supports (23) loosely on the
machine housing with two hexagon screws M6x30
and two washers M6 (b).
4. Align the table width extensions (10) and the table
extension (3) so that they are level in relation to
the saw table (2).
5. Tighten the threaded connections on the table
width extensions (10), on the table extension (3)
and on the saw table (2).
6. Leave the threaded connections on the machine
housing loose for the time being.
8.2 Fitting the base frame (fig. 6, 7)
1. Fasten the front legs (17) on the machine housing
with two Allen screws M6x30 and two washers (c)
(fig. 7).
2. Position one long centre strut (17) respectively
between two legs (18) on the front side (crank
wheel 15) and rear side (extraction port 21) of the
circular table saw (see fig. 6).
3. Secure the long centre struts (17) to the legs (18)
with a total of eight coach bolts M6×12, eight
washers and eight nuts M6 (d).
4. Position a short central strut (20) between two
support legs (18). Fix them to the support legs (18)
with a total of eight M6×12 carriage bolts, eight
washers and eight M6 nuts (d).
5. Push one rubber foot (19) onto each leg (18).
6. Carefully turn the saw table (2) over and stand it
on its legs (18) on the floor.
7. Now tighten all previously established threaded
connections.
8. NOTE: During this step, ensure that the table
width extensions and table extensions are cor-
rectly aligned with the saw table (2).
9. Tighten both pre-mounted nuts (B) on the rail joiners
(A).
8.3 Riving knife
m WARNING
Danger of injury due to unexpected start-up of the ma-
chine
- Pull the mains plug out of the outlet.
You need to remove the table inlay (5) before you can
install and adjust the riving knife (6).
8.3.1 Removing the table inlay (fig. 8)
1. Set the saw blade (7) to the max. cutting depth,
move to the 0° position and lock in place (see 10.2).
2. Remove the countersunk head screw (5a).
3. Remove the table inlay (5) from the saw table (2).
8.3.2 Installing and adjusting the riving knife
(fig. 8, 9)
1. Loosen the fixing screw (6a).
2. Push the riving knife (6) into the holder.
NOTE: This step can be skipped if the riving knife (6)
has already been installed.
3. Align the riving knife (6) such that
a) the distance between the saw blade (7) and the
riving knife (6) is max. 5 mm (fig. 9),
b) the saw blade (7) is parallel to the riving knife
(6) and
c) the recesses on the riving knife (6) engage in
the pins of the riving knife holder.
4. Tighten the fixing screw (6a) again.
8.3.3 Fitting the table inlay (fig. 8)
1. Place the table insert (5) in the recess.
2. Tighten the countersunk screw (5a).
8.4.1 Fitting the saw blade guard (fig. 10)
1. Place the saw blade guard (8) on the riving
knife (6) from above so that the screw (C) is
firmly placed in the slot of the riving knife (6).
Attention: Press the quick locking button (A) in
order to place the saw blade guard (8) on the riv-
ing knife (6).
www.scheppach.com
GB | 37