Maintenance; Transport; Storage - Scheppach HS730 Traduction Des Instructions D'origine

11. Maintenance

m Warning: Turn off the machine and disconnect
from the power supply before conducting mainte-
nance work or settings.
Store the manual close to the machine.
Keep the machine clean.
Wear goggles when cleaning the machine
Caution: Do not clean synthetic components of the
bench using aggressive cleaning agents. We recom-
mend a mild dish washing liquid. The machine must
not get into contact with water.
• Check the saw blade regularly. Use only well-
sharpened, crack-free and not distorted saws.
Use only tools that comply with the European
standard EN 847-1.
• Exchange immediately rocker that run out.
• Check all safety installations after each mainte-
nance and cleaning activities.
• Ensure that there are no tools or other materials on
or in the machine before putting it into operation.
• Remove possible sawdust blockages at the dis-
charge.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Saw blade, Rocker inlet
* Not necessarily included in the scope of delivery!
Change of saw blades fig. 11 - 15
m Remove the mains plug before changing the saw
blade.
m Danger of cutting! The saw blade is massive and
it could be to slick.
Wear gloves when replacing the saw blade.
• Do not use any saw blades made of HSS steel.
• Do not use any cracked saw blades or such that
have changed their shape.
• Only use well-sharpened saw blades.
m Danger of burning! The saw blade is still hot shortly
after cutting.
1. Firmly hold the tilt table pull out the spring cotter
pin (fig. 11, A).
2. Loosen the hexagonal nut (fig. 12 B), firmly hold
the tilt table and pull the swivel's guide rail (fig.
12 C) from the threaded pin (fig. 12 D).
3. Slowly lower the tilt table towards the ground.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
4. Use the locking pin (fig. 13, 14) to secure the saw
blade against turning.
5. Loosen the screw (fig. 14, E).
6. Remove the washer (fig. 14, F), the front saw
blade flange (fig. 14, G) and the saw blade (fig.
14, H).
7. Clean the saw blade flanges
8. Install a new or sharpened saw blade.
Pay attention to the correct running direction of
the saw blade: The arrow on the safety guard
and the arrow on the saw blade must show to the
same direction.
9. Reinstall the front saw blade flange and the
washer
10. Secure the saw blade using the screw.
11. Slide the both washers on the support pin
(fig. 15, I).
12. Lift the tilt table and guide the support pin into
the hole (fig. 15, J).
13. Insert the swivel's guide rail (fig. 12, C) to the
threaded pin (fig. 12, D) and fix it with the hex-
agonal nut (fig. 12, B)
14. Plug the spring cotter pins (fig. 11, A) through the
support pin (fig. 15, I).
15. Remove the locking pin (fig. 13, 14).
Replacing the plastics insert
Immediately replace the worn or damaged plastics
inserts (fig. 1, 11).
1. Loosen the screws of the plastics insert and re-
move them.
2. Insert a new plastic insert and screw it tightly in
place.

12. Transport

Transport fig. 9
Place the jack in the transport position and secure it
with the locking lever (18) fig. 2
Hold the handle, put one foot onto the axle and tilt the
machine towards your body
In this position it is easy to move the machine.
Attention! The saw may only be used when all four
feet are securely on the ground.

13. Storage

Store the equipment and accessories out of chil-
dren's reach in a dark and dry place at above freez-
ing temperature. The ideal storage temperature is
between 5 and 30 °C. Store the electric tool in its
original packaging.
GB | 25