Scheppach HS730 Traduction Des Instructions D'origine page 21

• To rectify faults or remove jammed pieces of wood,
always switch off the machine first. Pull the power
plug!
• If the sawing gap is worn, replace the table insert.
Pull the power plug!
• Carry out retooling work, adjustments, measure-
ments and cleaning jobs only when the motor is
switched off. Pull the power plug!
• Before switching on, make sure that all keys and
wrenches have been removed from the tool.
• Switch off the motor and pull the power plug before
you leave the workplace.
• Refit all guards and safety devices immediately
after you have completed any repairs or mainte-
nance work.
• Be sure to observe the safety information and op-
erating and maintenance instructions issued by the
manufacturer, as well as the dimensions listed in
the Technical Data.
• It is imperative to observe the accident prevention
regulations in force in your area as well as all other
generally recognized rules of safety.
• Note the information published by your professional
associations (VBG 7j).
• The circular saw has to be connected to a 400 V
socket with a 16 A fuse.
• Do not use any low-powered machines for heavy
duty work.
• Do not use the cable for purposes for which it is
not designed.
• Make sure you stand squarely and keep your bal-
ance at all times.
• Check the tool for damage.
• Each time before re-using the tool, carefully check
that the guards or any slightly damaged parts are
working as intended.
• Check that the moving parts are in good working
order, that they do not jam, and that no parts are
damaged. Make sure that all parts are fitted cor-
rectly and that all other operating conditions are
properly fulfilled.
• Unless otherwise stated in the operating instruc-
tions, damaged safety devices and parts must
be repaired or replaced by an authorized service
center.
• Have damaged switches replaced by a customer
service workshop.
• This electric tool complies with the pertinent safety
regulations. Repairs are to be carried out only by
a qualified electrician using original replacement
parts or the user may suffer an accident.
• If necessary, wear suitable personal protection
equipment. This could consist of:
• Ear plugs to prevent the risk of damaging your
hearing;
• A breathing mask to avoid the risk of inhaling haz-
ardous dust.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Always wear gloves when handling saw blades and
rough materials. Whenever practicable, saw blades
must be carried in a container.
• The operator must be informed about the condi-
tions that influence the generation of noise (for
example saw blades designed to reduce noise
emissions, caring for blades and the machine).
• Faults on the machine or its guards, safety devices
and blade must be reported to the person in charge
as soon as they are discovered.
• Use only the transport devices to move the ma-
chine. Never use the guards for handling and mov-
ing the machine.
• All operators must receive proper training in the
use, adjustment and operation of the machine.
• Do not saw any materials that contain foreign bod-
ies such as wires, cables or ties.
• Only use sharp saw blades
• The machine must stand during the operation on
a horizontal , flat floor and the floor around the
machine must be level, well maintained and free
of debris, such as Be chips and cut workpieces.
• Adequate general lighting or local lighting must be
available.
• Assign the workpiece to be machined and the stack
finished workpieces close to the normal work of
the operator.
• Make it adopt the safe procedures for cleaning,
maintenance and the regular removal of chips and
dust to avoid the risk of fire .
• Follow the instructions of the manufacturer for use
, adjustment and repair of saw blades.
• Note appearing on the blades maximum speed.
• Make sure that the flanges used are as specified by
the manufacturer , suitable for the intended use .
• Make sure you include that necessary for operat-
ing the machine guards and other safety devices
are fitted, they are in good operating condition and
properly maintained .
• The dust level is influenced by the type of material
to be cut.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can im-
pair active or passive medical implants under certain
conditions. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operating
the electric tool.
GB | 21