Scheppach DM460T Traduction Des Instructions D'origine page 14

Such defective electrical connection cables must not
be used as the insulation damage makes them ex-
tremely hazardous.
Check electrical connection cables regularly for dam-
age. Make sure the cable is disconnected from the
mains when checking.
Electrical connection cables must comply with the
regulations applicable in your country.
Single-phase motor, Fig. 06
• The mains voltage must coincide with the voltage
specified on the motor's rating plate.
• Extension cables up to a length of 25 m must have a
cross-section of 1.5 mm
2.5 mm .
2
• The connection to the mains must be protected with
a 16 A slow-acting fuse.
Only a qualified electrician is permitted to connect the
machine and complete repairs on its electrical equip-
ment.
In the event of enquiries please specify the following
data:
• Motor manufacturer
• Type of current of the motor
• Data recorded on the machine's rating plate
• Data recorded on the switch's rating plate
If a motor has to be returned, it must always be dis-
patched with the complete driving unit and switch.
Maintenance
Overhauls, maintenance work, cleaning, as well as
•
the elimination of any malfunctions must only be un-
dertaken after turning off the motor.
• All protective and safety equipment must be rein-
stalled immediately upon completion of any repair
or maintenance work.
• Clean and lightly oil the spindle thread of the tool
holder when changing tools.
• When possible, the tail stock sleeve should be re-
moved by unscrewing it, cleaned and then sprayed
with a dry lubricant. Grease the threaded spindle.
• Check the eccentric clamp of the tailstock as well as
the tool holder and adjust if necessary. In addition,
tighten the hex nut under the bracket.
• Check the drive belt and replace when necessary.
Accessories
Article
Turning lathe extension
Additional tools 5er set
Additional tools 6er set
Screw chuck
Socket chuck Ø 30 mm
Socket chuck Ø 40 mm
Socket chuck Ø 60 mm
Driver plate Ø 80 mm
Three-jaw chuck Ø 100 mm
Four-jaw chuck Ø 125 mm
Drill chuck 3 – 16 mm cone mandrel MK-2
7700
14 english
, and beyond 25 m at least
2
Art. No.
4902301701
88002716
88002717
7400 7200
7400 8600
7400 7300
7400 8700
7400 8800
7400 8900
7400 7400
7400
You can find other accessories in our current cata-
logue or at www.scheppach.com.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the follow-
ing parts are therefore also required for use as con-
sumables.
Wear parts*: Carbon brushes, v-belt
* Not necessarily included in the scope of delivery!
Disposal and recycling
The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Defective com-
ponents must be disposed of as special waste. Ask
your dealer or your local council.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must
not be disposed of together with domestic
waste in compliance with the Directive
(2012/19/EU) pertaining to waste electrical and
electronic equipment (WEEE). This product must be
disposed of at a designated collection point. This can
occur, for example, by handing it in at an authorised
collecting point for the recycling of waste electrical
and electronic equipment. Improper handling of waste
equipment may have negative consequences for the
environment and human health due to potentially haz-
ardous substances that are often contained in electri-
cal and electronic equipment. By properly disposing
of this product, you are also contributing to the effec-
tive use of natural resources. You can obtain informa-
tion on collection points for waste equipment from
your municipal administration, public waste disposal
authority, an authorised body for the disposal of
waste electrical and electronic equipment or your
waste disposal company.