Bosch GTS 10 XC Professional Notice Originale page 40

OBJ_BUCH-1375-005.book Page 40 Friday, March 16, 2018 9:47 AM
40 | English
– Move handwheel 19 toward the 0° stop until the leg of the
angle gauge is flush with the saw blade over the complete
length.
– Hold the handwheel in this position and tighten locking le-
ver 26 again.
– Tighten screw 67 again.
When the angle indicator 61 is not in line with the 0° mark of
scale 27, loosen screw 68 with a commercially available
cross-head screwdriver and align the angle indicator along-
side the 0° mark.
Repeat the above mentioned worksteps accordingly for the
45° bevel angle (loosening screw 69; moving the 45° stop
25). In this, the angle indicator 61 must not be misadjusted.
Parallelism of the Saw Blade to the Guide Grooves of the
Angle Stop (see figure N)
– Bring the power tool into the working position.
– Tilt the blade guard 5.x toward the rear to the stop.
Checking:
– With a pencil, mark the first visible saw tooth on the left
side that projects above the insert plate.
– Set an angle gauge to 90° and place it on the edge of the
guide groove 9.
– Move the leg of the angle gauge until it touches the marked
saw tooth, and read the clearance between saw blade and
guide groove.
– Turn the saw blade until the marked tooth projects above
the right side of the insert plate.
– Move the angle gauge alongside the guide groove to the
marked tooth.
– Measure the clearance between the saw blade and guide
groove again.
Both clearances measured must be identical.
Adjusting:
– Loosen hex socket screws 70 at the front below the saw ta-
ble and hex socket screws 71 at the rear below the saw ta-
ble with the supplied hex key 37.
– Carefully move the saw blade until it is parallel to guide
groove 9.
– Retighten all screws 70 and 71 again.
Adjusting the Saw Table's Clearance Indicator
(see figure O)
– Position the parallel guide on the right side of the saw
blade.
Move the parallel guide until the mark in the lens 64 indi-
cates 33 cm on the bottom scale.
To lock the parallel guide, press clamping handle 47 down
again.
– Completely pull clamping handle 18 upward and pull the
table width enlargement 11 outward to the stop.
Checking:
On the upper scale 1, clearance indicator 65 must indicate
the identical value as the mark in lens 64 on the bottom scale
1.
Adjusting:
– Loosen screw 72 with a cross-head screwdriver and align
clearance indicator 65 alongside the 33 cm mark of the up-
per scale 1.
1 609 92A 467 | (16.3.18)
Adjusting the Parallelism of the Parallel Guide
(see figure P)
– Bring the power tool into the working position.
– Tilt the blade guard 5.x toward the rear to the stop.
– Loosen the clamping handle 47 of the parallel guide and
slide it until it touches the saw blade.
Checking:
The parallel guide 8 must touch the saw blade over the com-
plete length.
Adjusting:
– Loosen the hex socket screws 82 using the supplied hex
key 37.
– Carefully move the parallel guide 8 until it touches the saw
blade over the complete length.
– Hold the parallel guide in this position and press the clamp-
ing handle 47 down again.
– Retighten the hex socket screws 82.
Adjusting the Tension Force of the Parallel Guide
The tensioning force of the parallel guide 8 can decrease after
frequent usage.
– Tighten the adjusting screw 81 until the parallel guide can
be securely fixed to the saw table again.
Adjusting the Lens of the Parallel Guide (see figure P)
– Bring the power tool into the working position.
– Tilt the blade guard 5.x toward the rear to the stop.
– Move parallel guide 8 from the right until it touches the saw
blade.
Checking:
The mark of lens 64 must be in a line with the 0° mark of scale
1.
Adjusting:
– Loosen screw 73 using a cross-head screwdriver and align
the clearance indicator alongside the 0° mark.
Adjusting the Level of the Insert Plate (see figure Q)
Checking:
The front side of the insert plate 31 must be flush with or
somewhat lower than the saw table; the rear side must be
flush with or somewhat above the saw table.
Adjusting:
– Adjust the correct level of the four adjusting screws 74
with a suitable slotted screwdriver.
Storage and Transport
Storing Product Features (see figures R1–R6)
For storage purposes, certain product features can be se-
curely fastened to the power tool.
– Loosen auxiliary parallel guide 49 from parallel guide 8.
– Attach all loose tool parts to their storage locations on the
housing. (see Table)
Fig- Product Feature Storage Location
ure
R1 Blade guard 5.x Insert into the recess of fixture
22 and tighten with clamping le-
ver 46.1 or clamping screw
46.2
Bosch Power Tools