Bosch GTS 10 XC Professional Notice Originale page 39

OBJ_BUCH-1375-005.book Page 39 Friday, March 16, 2018 9:47 AM
Protect the saw blade against impact and shock. Do not sub-
ject the saw blade to lateral pressure.
The riving knife must be in alignment with the saw blade to
avoid jamming of the workpiece.
Do not saw warped/bent workpieces. The workpiece must al-
ways have a straight edge to face against the parallel guide.
Always keep/store the push stick with the power tool.
Position of the Operator (see figure J)
 Do not stand in a line with the saw blade in front of the
machine. Always stand aside of the saw blade. This pro-
tects your body against possible kickback.
– Keep hands, fingers and arms away from the rotating saw
blade.
Observe the following instructions:
– Hold the workpiece securely with both hands and press it
firmly against the saw table.
– When sawing narrow workpieces and bevel angles, always
use the supplied push stick 13 and the auxiliary parallel
guide 49.
Marking the Cutting Line (see figure K)
– Mark the saw blade width on the round yellow sticker 33.
This allows for exact positioning of the workpiece for saw-
ing, without having to open the blade guard.
Maximum Workpiece Dimensions
Bevel angle
0°
45°
Sawing
Sawing Straight Cuts
– Adjust the parallel guide 8 to the requested cutting width.
– (see "Adjusting the Parallel Guide", page 38)
– Position the workpiece on the saw table in front of the
blade guard 5.x.
– Raise or lower the saw blade with the crank 20 so that the
upper saw teeth project approx. 5 mm above the work-
piece surface.
– Adjust the blade guard according to the workpiece height.
When sawing, the blade guard must always face lightly
against the workpiece.
– Switch on the machine.
– Saw through the workpiece applying uniform feed.
– Switch off the machine and wait until the saw blade has
come to a complete stop.
Sawing Bevel Angles
– Adjust the desired bevel angle. (see "Adjusting Bevel An-
gles", page 37)
– Follow the worksteps in section "Sawing Straight Cuts" ac-
cordingly.
Sawing Mitre Angles (see figure L)
– Adjust the requested mitre angle. (see "Adjusting Mitre An-
gles", page 37)
Bosch Power Tools
– Place the workpiece against profile rail 34.
– Raise or lower the saw blade with the crank 20 so that the
– Adjust the blade guard according to the workpiece height.
– Switch on the machine.
– With one hand, press the workpiece against the profile rail
– Switch off the machine and wait until the saw blade has
Sawing Mitre Angles with the Sliding Table Locked
– Adjust the requested mitre angle. (see "Adjusting Mitre An-
– The angle stop must move freely in the guide groove 9 (left-
– Follow the worksteps in section "Sawing Straight Cuts" ac-
Sawing Mitre Angles with the Sliding Table
– Adjust the requested mitre angle. (see "Adjusting Mitre An-
– Completely pull clamping handle 29 for the sliding table
Max. workpiece height
[mm]
– Position the workpiece on the saw table in front of the
79
56
– Position the angle stop 3 in front of the workpiece in the
– Follow the worksteps in section "Sawing Straight Cuts" ac-
Checking and Adjusting the Basic Adjustment
To ensure precise cuts, the basic adjustment of the machine
must be checked and adjusted as necessary after intensive
use.
A certain level of experience and appropriate specialty tools
are required for this.
A Bosch after-sales service station will handle this mainte-
nance task quickly and reliably.
Setting the Stops for Standard 0°/ 45° Bevel Angles
– Bring the power tool into the working position.
– Adjust to a 0° bevel angle.
– Tilt the blade guard 5.x toward the rear to the stop.
Checking: (see figure M1)
– Set an angle gauge to 90° and place it on the saw table 17.
The leg of the angle gauge must be flush with the saw blade 32
over the complete length.
Adjusting: (see figure M2)
– Loosen screw 67.
– Loosen locking lever 26.
The profile may not be on the cutting line. If so, loosen
knurled nut 53 and move the profile.
upper saw teeth project approx. 5 mm above the work-
piece surface.
When sawing, the blade guard must always face lightly
against the workpiece.
and with the other hand, slowly move the angle stop via
locking knob 62 toward the front in guide groove 9.
come to a complete stop.
gles", page 37)
ward or rightward).
For this, loosen knurled screw 51, if required.
cordingly.
gles", page 37)
upward and pull the sliding table 2 toward the front.
blade guard 5.x.
lefthand guide groove 9. Lock this position by firmly tight-
ening the knurled screw 51.
cordingly.
The 0° stop 28 can now be moved.
English | 39
1 609 92A 467 | (16.3.18)