Bosch GTS 10 XC Professional Notice Originale page 35

OBJ_BUCH-1375-005.book Page 35 Friday, March 16, 2018 9:47 AM
Assembly
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Please also observe the representation of the
delivery scope at the beginning of the operat-
ing instructions.
Before starting the operation of the machine
for the first time, check if all parts listed below
have been supplied:
– Table saw with mounted saw blade 32 and riving knife 7
– Angle stop 3
– Profile rail 34
– Fastening kit "profile rail" 52 (guide plate, knurled nut,
screw, washer)
– Parallel guide 8
– Auxiliary parallel guide 49
– "Auxiliary parallel guide" fastening kit 39 (3 fastening
screws, 3 washers, 3 wing nuts)
– Blade guard 5.x*
* depending on country version: 5.1/5.2
– Table extension 10
– Fastening kit for "table extension"43
(2 fastening screws, 2 washers, 1 open-end spanner)
– Hex key 37
– Ring spanner 15
– Cover of the saw blade storage 14
– Push stick 13
– Insert plate 31
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Mounting Individual Components
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packaging material from the machine and the
accessories provided.
– Open the bottom plate 44 and remove the packaging ma-
terial under the motor block. (see figure a)
The following product features are fastened directly to the
housing:
Push stick 13, ring spanner 15, Allen key 37, parallel guide 8,
angle guide 3, extraction adapter 41, auxiliary parallel guide
49 with fastening kit 39, blade guard 5.x.
– Carefully remove these product features from their stor-
age locations.
Also see figures R1–R6.
Additionally required tools (not in delivery scope):
– Slotted screwdriver
Bosch Power Tools
– Cross-head screwdriver
– Angle gauge
Mounting the Insert Plate (see figure b)
– Hook insert plate 31 into the rear insert-plate notches 45
of the tool basin.
– Guide the insert plate down.
– Press on the insert plate until it engages at the front in the
tool basin.
The front side of the insert plate 31 must be flush with or
somewhat lower than the saw table; the rear side must be
flush with or somewhat above the saw table. (also see "Ad-
justing the Level of the Insert Plate", page 40)
Mounting the blade guard* (see figure c)
* depending on country version
– Turn crank 20 clockwise to the stop, so that the saw blade
32 is in the highest possible position above the saw table.
– Insert the blade guard 5.x into the recess in riving knife 7.
– Tighten the clamping lever 46.1.
or
Tighten clamping screw 46.2 with hex key 37.
– Adjust the blade guard according to the workpiece height.
When sawing, the blade guard must always face lightly
against the workpiece.
Note: Clamping lever 46.1 is indexed (adjustable), allowing it
to be set to an ergonomically favourable or space-saving posi-
tion.
With the clamping lever tightened, pull its lever away from the
blade guard, turn it to the desired position and allow it to en-
gage again.
Mounting the Table Extension (see figure d)
For assembly, use the fastening kit for "table extension" 43.
(2 fastening screws, 2 washers, 1 open-end spanner)
– Bolt the table extension 10 with the guide rods 24.
When doing this, the recesses in the table extension must
face upward.
Mounting the Parallel Guide (see figure e)
The parallel guide 8 can be positioned either left or right from
the saw blade.
– Loosen clamping handle 47 of parallel guide 8.
This releases V-guide 48.
– Firstly, mount the parallel guide via the V-guide in guide
groove 30 of the saw table. Now, position the parallel
guide into the front guide groove 35 of the saw table.
The parallel guide can now be moved to any position.
– To lock the parallel guide, press the clamping handle 47
down.
Mounting the Auxiliary Parallel Guide (see figure f)
When sawing narrow workpieces and bevel angles, the
auxiliary parallel guide 49 must be mounted to parallel guide
8.
The auxiliary parallel guide can be mounted left or right from
parallel guide 8, as required.
For assembly, use the "auxiliary parallel guide" fastening kit
39. (3 fastening screws, 3 washers, 3 wing nuts)
English | 35
1 609 92A 467 | (16.3.18)