Horizon Hobby Hobby Zone Apprentice STOL S 700mm Manuel D'utilisation page 19

Bind and Fly Transmitter Setup
IMPORTANT: This aircraft is compatible with Spektrum transmitters. Binding
to an SLT transmitter other than the Spektrum SLT6LP will not provide full
functionality.
To use a Spektrum DSMX transmitter, follow the setup instructions on this page
which corresponds to your DX, NX or iX series transmitter.
When using the recommended setup, the transmitter switch layout is as follows:
• Switch B Selects the Flight mode; Beginner (position 0),
Intermediate (position 1), Experienced (position 2)
• Button I controls the Panic mode (depressed activates Panic mode)
• Switch F controls the aileron dual rates
• Switch C controls the elevator dual rates
• Switch G controls the rudder dual rates.
• Switch H controls the throttle cut.
Dual Rates
Make the initial flights in low rate, changing to high rate elevator for landing.
NOTICE: To ensure AS3X technology functions properly, do not lower rate
values below 50%. If less control deflection is desired, manually adjust the
position of the pushrods on the servo arm
NOTICE: If oscillation occurs at high speed, refer to the Troubleshooting
Guide for more information.
Exponential
After first flights, adjust the exponential settings in the transmitter to fine tune
the responsiveness of the aircraft around neutral to your preference.
iX Series Transmitter Setup
1. Power ON your transmitter and begin once the Spektrtum Airware app is open.
Select the orange pen icon in the upper left corner of the screen, the system
asks for permission to Turn Off RF, select PROCEED
2. Select the three dots in the upper right corner of the screen,
select Add a New Model
3. Select Model Option, choose DEFAULT, select Airplane.
The system asks if you want to create a new acro model, select Create
4. Select the last model on the list, named Acro.
Tap on the word Acro and rename the file to a name of your choice
5. Tap and hold the back arrow icon in the upper left corner of the screen to
return to the main screen
6. Go to Model Setup;
Select Channel Assign, select PROCEED
5 Gear: Switch B
6 Aux1: Switch I
Press and hold the back arrow icon in the upper left corner of the screen
to return to the main screen
7. Go to the Model Adjust menu
8. Select Dual Rates and Expo;
Channel: Aileron
Switch: Switch F
Set Switch Positions 0 and 1: Rate 100%, Expo 10%
Set Switch Position 2: Rate 70%, Expo 5%
9. Channel: Elevator
Switch: Switch C
Set Switch Positions 0 and 1: Rate 100%, Expo 10%
Set Switch Position 2: Rate 70%, Expo 5%
10. Channel: Aileron
Switch: Switch G
Set Switch Positions 0 and 1: Rate 100%, Expo 10%
Set Switch Position 2: Rate 70%, Expo 5%
11. Tap the back arrow to return to the Model Adjust menu
12. Select Throttle Cut;
Switch: Switch H
Position: -100%
NX Series Transmitter Setup
1. Power ON your transmitter, click on scroll wheel, roll to System Setup and
click the scroll wheel. Choose yes.
2. Go to Model Select and choose <Add New Model> near the bottom of the
list. Select Airplane Model Type by choosing the airplane, select Create
3. Set Model Name: Input a name for your model file
4. Go to Channel Assign
5 Gear: Change A to Switch B
6 Aux1: Change D to Button I
Click List to exit
5. Select <Main Screen>, Click the scroll wheel to enter the Function List
6. Go to D/R (Dual Rate) and Expo;
Channel: Aileron
Set Switch: Switch F
Set Switch Positions 0 and 1: Rate 100%, Expo 10%
Set Switch Position 2: Rate 70%, Expo 5%
7. Go to D/R (Dual Rate) and Expo;
Channel: Elevator
Set Switch: Switch C
Set Switch Positions 0 and 1: Rate 100%, Expo 10%
Set Switch Position 2: Rate 70%, Expo 5%
8. Go to D/R (Dual Rate) and Expo;
Channel: Rudder
Set Switch: Switch G
Set Switch Positions 0 and 1: Rate 100%, Expo 10%
Set Switch Position 2: Rate 70%, Expo 5%
9. Select List to go back to the Function List
10. Select Throttle Cut;
Switch: Switch H
Position: -100%
DX Series Transmitter Setup
1. Power ON your transmitter, click on scroll wheel, roll to System Setup and
click the scroll wheel. Choose yes.
2. Go to Model Select and choose <Add New Model> at the bottom of the
list. The system asks if you want to create a new model, select Create
3. Set Model Type: Select Airplane Model Type by choosing the airplane.
The system asks you to confirm model type, data will be reset. Select YES
4. Set Model Name: Input a name for your model file
5. Select <Main Screen>, Click the scroll wheel to enter the Function List
6. Go to D/R (Dual Rate) and Expo;
Channel: Aileron
Set Switch: Switch F
Set Switch Positions 0 and 1: Rate 100%, Expo 10%
Set Switch Position 2: Rate 70%, Expo 5%
7. Go to D/R (Dual Rate) and Expo;
Channel: Elevator
Set Switch: Switch C
Set Switch Positions 0 and 1: Rate 100%, Expo 10%
Set Switch Position 2: Rate 70%, Expo 5%
8. Go to D/R (Dual Rate) and Expo;
Channel: Rudder
Set Switch: Switch G
Set Switch Positions 0 and 1: Rate 100%, Expo 10%
Set Switch Position 2: Rate 70%, Expo 5%
9. Select List to go back to the Function List
10. Select Throttle Cut;
Switch: Switch H
Position: -100%
19
Apprentice STOL S 700mm
®
EN