Seat Depth - Quickie SOPUR P-220 Manuel D'utilisation Et Garantie

I X . S e t - u p , A d j u s t m e n t s a n d U s e
J. SINGLE-POST HEIGHT-ADJUSTABLE ARMRESTS (OPTIONAL)
1. Installation
a. Slide the outer armpost into the receiver mounted to the wheelchair frame.
b. The armrest will automatically lock into place.
2. Height adjustment
a. Rotate release lever to stop.
b. Slide armrest pad up or down to desired height.
c. Return lever to locked position.
d. Push arm pad until upper armpost locks firmly into place.
3. Removing armrest
a. Rotate release lever and remove the armrest.
4. Replacing armrest
a. Slide armrest back into receiver.
b. Return release lever to locked position against armpost.
5. Adjusting armrest receiver fit
To tighten or loosen the fit of the outer armpost in the receiver:
a. Loosen the four bolts on the sides of the receiver.
b. With the armrest in the receiver, squeeze the receiver to achieve the desired fit.
c. Tighten the four bolts.
6. Adjusting inner armpost fit
a. Two set screws are installed in the outer armpost.
b. Turn the set screws in or out until the desired fit is achieved.
K. SEAT DEPTH
The seat depth can be adjusted in one inch increments.
1. Seat frame depth adjustment
a. To adjust, remove the two bolts (C and D) from each side of the backrest pivot plate.
b. Reposition the backrest to the desired position.
c. Replace and retighten bolts on each side of the backrest pivot plate.
2. Back angle adjustment on seat frame
a. Remove the front securing bolt (C) on the side of the backrest hinge plate.
b. Loosen the lower rear bolt (D).
c. Set at desired angle. There are five holes (in 4º increments) to choose from.
d. Reinstall the front bolt and tighten both bolts securely
L. 12" (300mm) DRIVE WHEEL
Drive wheel position adjustment
a. Remove the seat and main frame and the batteries.
b. Remove the four (4) bolts (B) using a 1/2" wrench from each quick-connect socket.
c. Move the socket forward or backwards to the desired position.
d. Reinstall the four (4) bolts in the quick-connect socket. Use a torque setting of 240
in.-lbs. (27 Nm) to tighten bolts.
M. DYNAM1C STABILISER
4" (100 mm) rear wheel adjustment
a. Remove rear batteries.
b. Remove the upper pivot bolt (A) on the rear whee1 spring.
c. Set at desired height.
d. Tighten nut. Use a torque setting of 240 in.-lbs. (27 Nm) to tighten nut.
e. Height adjustment may also be made by using extra set of mounting holes on rear
wheel mount bracket.
NOTE– The lowest point of the rear wheels should be 1/4" to 1/2" (6 to 13 mm) from the ground to allow
for proper clearance (with the tyres properly inflated and user sitting in the chair). A smaller clear-
ance produces less rocking motion, and a larger clearance allows easier movement on deep carpets.
NOTE– In addition to the user's weight, the seat depth and back angle adjustment will affect this
choice. Choose the position that provides the most comfortable transition onto and off the
dynamic stabiliser wheels.
All manuals and user guides at all-guides.com
E n g l i s h
4
5
3
1
7
2 8
6
9
Height-Adjustable Armrest Key
1. Inner Arm Post
2. Receiver
3. Release Lever, Locked Position
4. Armrest Pad
5. Transfer Bar
6. Side Panel
7. Tension Adjustment Set Screw
8. Outer Arm Post
9. Receiver Adjustment Bolts
D
C
D
C
B
A
23
930479 Rev. C