Storage; Disposal And Recycling - Scheppach MFH5300-4BP Traduction Des Instructions D'origine

These parts include, among others, the cutting tool
and the retaining disk.
m Warning!
Use only original manufacturer's replacement parts,
accessories and attachments. Failure to do so can
cause poor performance, possible injury and may
void your warranty.
Important hint in case of sending the equipment
to a service station:
Due to security reasons please see to it that the
equipment is sent back free of oil and gas!
Ordering replacement parts
Please quote the following data when ordering re-
placement parts:
• Type of machine
• Article number of the machine
Replacement parts / accesories:
For the cutting equipment listed here, you can always
use the safety guards provided with the unit.
Grass trimmer/brush cutter:
Spool with Ø 450
Blade with 3 teeth Ø 255 x 1,4
Transport guard for blade 3 teeth
Blade with 4 teeth Ø 255 x 1,5
Transport guard for blade 4 teeth
Blade with 8 teeth Ø 255 x 1,5
Transport guard for blade 8 teeth
Safety shield for grass trimmer
Pole pruner:
Saw chain Oregon 91PJ040X
Guide rail Oregon 100SDEA318
Transport guard for chain
Extension for pole pruner
Hedge trimmer:
Blade for hedge trimmer 400 mm
Transport guard for blade 400 mm

11. Storage

Cleaning
• Keep handles free of oil, so you always have a se-
cure hold.
• Clean the equipment as required with a damp cloth
and, if necessary, mild washing up liquid.
m Important!
• Always pull out the spark boot plug each time be-
fore carrying out any cleaning.
• Never immerse the equipment in water or other liq-
uids in order to clean it.
• Store the petrol multi garden tool in a safe and dry
place out of the reach of children.
Storage
Important: Never put the equipment into storage for
longer than 30 days without carrying out the follow-
ing steps.
42 GB
Storing the equipment
If you intend to store the equipment for longer than 30
days, the equipment must be prepared accordingly.
Otherwise the fuel still remaining in the carburetor will
evaporate and leave a rubbery sediment. This can
cause problems when starting up the equipment and
may require expensive repairs.
1 Slowly remove the fuel tank cap to release any
2 To remove the fuel from the carburetor, start the
3 Leave the engine to cool (approx. 5 minutes).
4 Remove the spark plug (see section 10 Change
5 Add one teaspoon of 2-stroke engine oil into the
7910700707 Note: Store the equipment in a dry place and far
7910700702 away from possible ignition sources such as an oven,
3904801065 a gas fired hot water boiler, a gas fired dryer, etc.
7910700705
3904801066 Putting the equipment back into operation
7910700711 1 Remove the spark plug (see section 10 Change
3904801066
3904803034 2 Quickly tug on the starter cord to remove excess
7910700704 3 Clean the spark plug and check that the electrode
3904801037
3904801039
7910700710 4 Prepare the equipment for operation.
Transport
7910700703
3904801043 To transport the machine, empty the petrol tank as
described in section 8 draining fuel. Clean coarse dirt
off the equipment with a brush or hand brush.
Always attach the transport guard to all cutting tools.
Fig. 1 (14a, 15a, 17a)
In order to prevent damage and injury, secure the tool
against tipping over and sliding when transporting it
in vehicles.

12. Disposal and recycling

The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Defective
components must be disposed of as special waste.
Ask your dealer or your local council.
pressure that may have formed in the tank. Care-
fully empty the tank. Only empty the tank out-
doors or in well-ventilated rooms. Make sure
that no fuel or chain oil is released into the
soil (environmental protection). Use a suit-
able surface.
engine and let it run until the equipment stops.
and clean the spark plug).
combustion chamber. Slowly pull the starter cord
several times to apply a layer of oil to all internal
components. Fit the spark plug again.
and clean the spark plug).
oil from the combustion chamber.
gap is correct, or insert a new spark plug with the
correct electrode gap.