Storage; Disposal And Recycling - Scheppach MFH5300-4BP Traduction Du Manuel D'origine

depth gauge.
• File down. The knife is always from the inside to the
outside
• The file sharpens only in forward motion. Lift it off in
the backward motion.
• Do not touch the dynamic links with the file.
• Turn the file regularly continue to avoid a onesided
wear.
• Remove to remove a piece of hard wood, bones raw
edges.
All knives must have the same length, otherwise they
will also vary. As a result, the chain is irregular and it
increases the risk of going broke.
Lubricate angle transmission
Lubricate with lithium-based grease. Remove the screw
and put in the grease, turning the shaft manually until
grease emerges, then replace the screw.
Storing the unit
After cutting, clean the unit thoroughly. Store the unit in a
dry room allow the motor to cool down beforehand.
Important hint in case of sending the equipment to a
service station:
Due to security reasons please see to it that the
equipment is sent back free of oil and gas!
Ordering replacement parts
Please quote the following data when ordering
replacement
parts:
• Type of machine
• Article number of the machine
Replacement parts:
Saw chain 10" Oregon 91PJ040X
Chain saw blade 10" Oregon 100SDEA318

11. Storage

Cleaning
• Keep handles free of oil, so you always have a secure hold.
• Clean the equipment as required with a damp cloth
and, if necessary, mild washing up liquid.
m Important!
• Always pull out the spark boot plug each time before
carrying out any cleaning.
• Never immerse the equipment in water or other liquids
in order to clean it.
• Store the petrol multi garden tool in a safe and dry
place out of the reach of children.
Storage
Important: Never put the equipment into storage for
Art.-No.: 7910700704
Art.-No.: 3904801037
longer than 30 days without carrying out the following
steps.
Storing the equipment
If you intend to store the equipment for longer than 30
days, the equipment must be prepared accordingly.
Otherwise the fuel still remaining in the carburetor will
evaporate and leave a rubbery sediment. This can cau-
se problems when starting up the equipment and may
require expensive repairs.
1 Slowly remove the fuel tank cap to release any pres-
sure that may have formed in the tank. Carefully empty
the tank.
2 To remove the fuel from the carburetor, start the engine
and let it run until the equipment stops.
3 Leave the engine to cool (approx. 5 minutes).
4 Remove the spark plug (see section 10 Change and
clean the spark plug).
5 Add one teaspoon of 2-stroke engine oil into the com-
bustion chamber. Slowly pull the starter cord several
times to apply a layer of oil to all internal components.
Fit the spark plug again.
Note: Store the equipment in a dry place and far away
from possible ignition sources such as an oven, a gas-fi
red hot water boiler, a gas-fi red dryer, etc.
Putting the equipment back into operation
1 Remove the spark plug (see section 10 Change and
clean the spark plug).
2 Quickly tug on the starter cord to remove excess oil
from the combustion chamber.
3 Clean the spark plug and check that the electrode gap
is correct, or insert a new spark plug with the correct
electrode gap.
4 Prepare the equipment for operation.
5 Fill the tank with the relevant mixture of fuel and oil.
See the section „Fuel and oil".
Transport
To transport the machine, empty the petrol tank as
described in section 8 draining fuel. Clean coarse dirt off
the equipment with a brush or hand brush.

12. Disposal and recycling

The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types of
material, such as metal and plastic. Defective compo-
nents must be disposed of as special waste. Ask your
dealer or your local council.
GB 39