Mounting The Snubber - Rohloff Gates SPEEDHUB 500/14 Manuel D'utilisation

Snubber-Clip-DIN6799-RA8
Snubber-long slot bolt
Snubber-long slot washer
Illustration 1:
Rohloff SPEEDHUB 500/14
with Snubber
Distance: 1-1,5 mm
Illustration 2:
The Snubber wheel does
not touch the belt!
20
Illustration 3:
Side view of the installed
Snubber
Circlip
26
11202008
11202009
mounting
11202010

Mounting the Snubber

Mounting the Snubber
1. The following illustration shows the Snubber
1. The following illustration shows the Snubber
mounted to the derailleur hanger. To mount the
mounted to the derailleur hanger. To mount the
Snubber, you have to affix the Snubber plate in
Snubber, you have to affix the Snubber plate in
the thread of the derailleur hanger with a M10x1
the thread of the derailleur hanger with a M10x1
screw. Then you have to affix the slidable Snubber
screw. Then you have to affix the sliding Snubber
axle to the Snubber plate with a M4 screw.
axle to the Snubber plate with a M4 screw.
2. The Snubber wheel is located on the Snubber axle.
2. The Snubber wheel is located on the Snubber
The Snubber wheel is slidable on the Snubber
axle. The Snubber wheel is sliding on the Snubber
axle. The Snubber wheel latches into an inner and
axle. The Snubber wheel latches into an inner and
an outer catch position on the axle, to ease the
an outer catch position on the axle, to ease the
dismounting of the wheel. The Snubber does not
dismounting of the wheel. The Snubber does not
influence the degree of efficiency or the smooth
influence the degree of efficiency or the smooth
operation of the belt, as it does not touch the
operation of the belt, as it does not touch the
belt. The Snubber is only for safety purposes.
belt. The Snubber is only for safety purposes.
3. The Snubber plate is screwed to the derailleur hanger
3. The Snubber plate is screwed to the derailleur hanger
with an M10x1 screw. The correct position is shown
with an M10x1 screw. The correct position is shown
in illustration 2. The center pin support has to be
in illustration 2. The center pin support has to be
pushed against the locating surface of the derailleur
pushed against the locating surface of the derailleur
hanger. The Snubber axle can be adjusted in an
hanger. The Snubber axle can be adjusted in an
elongated slot and it can be affixed with a M6 screw.
elongated slot and it can be affixed with a M6 screw.
The Snubber wheel can be slid along the Snubber
axle. If the Snubber is located in the left position, it is
active and can keep the belt from ratcheting, since the
The Snubber wheel can be slid along the Snubber
belt cannot slide across the teeth of the rear sprocket.
axle. If the Snubber is located in the left position, it is
When you adjust the position of the Snubber wheel,
active and can keep the belt from ratcheting, since the
make sure that the wheel does not touch the belt.
belt cannot slide across the teeth of the rear sprocket.
When you adjust the position of the Snubber wheel,
4. By moving the Snubber axle in the elongated slot
make sure that the wheel does not touch the belt.
of the Snubber plate, you can adjust the distance
between the Snubber wheel and the belt. This
4. By moving the Snubber axle in the elongated slot
distance should be between 1mm and 1.5mm.
of the Snubber plate, you can adjust the distance
between the Snubber wheel and the belt. This
distance should be between 1mm and 1.5mm.
Locating Surface
Snubber
Snubberaxle
mounting
Derailleur Hanger
2