Replacing Bulbs; Rear Drive Unit; Front Drive Unit (4Wd Model); Regulating The Grass Catcher Retaining Pawl Spring - EMAK KTK 102H Série Manuel D'utilisation

– 15 A fuse = protects the command motor
circuit, when it blows the electrical grass
catcher bag tipping system is disabled; in
this condition it is still possible to tip the
bag by using the manual lever (if fitted).
The fuse capacity is indicated on the fuse.
IMPORTANT A blown fuse must always
be replaced by one of the same type and
amperage and never with one of another rating.
If you are unable to understand why
it has blown contact Your Dealer.

8.6 REPLACING BULBS

8.6.1 Type "l" - Incandescent light bulbs
• The bulbs (18W) have a bayonet fitting
and are installed in the bulb holder,
which can be taken out by turning it
anti-clockwise with pliers (fig. 50).
8.6.2 Type "ll" - LED light bulbs
• Loosen the lock nut (fig. 51.A) and
remove the connector (fig. 51.B).
Remove the LED illuminator (fig. 51.C),
secured by screws (fig. 51.D).
8.6.3 Type "III" - LED light bulbs
(for TNS, THNS models)
1. Raise the bonnet and remove
the connector (fig. 52.A).
2. Detach the cotter pin (fig. 52.B) and
slide the bonnet off laterally.
3. Detach the LED light bulb cables (fig.
53.A), undo the screws (fig. 53.B)
and release the tabs (fig. 53.C).
4. Raise and release the upper part
of the bonnet (fig. 54.A).
5. Undo the screws (fig. 55.A) and replace
the LED headlights (fig. 55.B).
6. To replace the bonnet, repeat the
above procedure in reverse order.

8.7 REAR DRIVE UNIT

This is a sealed single unit that does not require
maintenance. It is permanently lubricated and its
lubricant does not need changing or topping up.

8.8 FRONT DRIVE UNIT (4WD MODEL)

This is a sealed single unit that does not
require maintenance. It is necessary to check
the oil in the hydraulic coupling circuit, top
it up and change it at regular intervals.
Check that the oil level in the hydraulic
system is between the «MIN» and
«MAX» markers on the tank.
If the level is below the «MIN»
reference marker (Fig. 56):
– remove the guard (fig. 56.A), which
is secured by the nut (fig. 56.B):
– unscrew the plug (fig. 56.C) and top
up using 10W30 oil until the level
reaches the «MAX» marker:
– replace the plug (fig. 56.C)
and the guard (fig. 56.A).
IMPORTANT If it becomes necessary to
top-up the oil level frequently, check the oil
tubes and tank for leaks and contact your
Dealer for the necessary maintenance.
8.9 REGULATING THE GRASS
CATCHER RETAINING
PAWL SPRING
If the grass catcher bag tends to jolt or
open unexpectedly while driving over
uneven ground, or if it is difficult to
recouple the retaining pawl after emptying
the bag, it may be necessary to adjust
the tension on the spring (fig. 57.A).
Adjust the mounting point by selecting the
hole (fig. 57.B) that provides the desired result.

9. STORAGE

When you intend to put your machine
away for more than 30 days:
1. Wait for the engine to cool
2. Disconnect the battery cables and
store it in a cool and dry place.
3. Empty the fuel tank (par. 7.2.2) and follow
all the instructions in the engine manual.
4. Clean the machine thoroughly.
5. Check the machine for any
damage. If necessary, contact the
Authorised Service Centre.
6. Store the machine:
– with the cutting device assembly lowered
– in a dry place
EN - 25