ATIKA BWS 400 Notice Originale - Consignes De Sécurité - Pièces De Rechange page 9

Do not operate machine before having read the
operating instructions, understood all the notes and
assembly the machine as described here.
Keep the instructions in a safe place for future use.
Contents
Declaration of conformity
Description of device / Spare parts
Extent of delivery
Characteristics noise values
Operating times
Symbols: machine
operating manual
Normal intended use
Risidual risks
Safety working
Assembling
Before the first start-up
Start-up
Working with the saw
Maintenance and cleaning
−
Changing the saw blade
−
Replacing the plastics insert
−
Replacing the recuperating spring
Transport
Storage
Possible faults
Technical data
Guarantee
EC Declaration of Conformity
No. (S-No.): 10497
according to EC directive 2006/42/EC
We,
ATIKA GmbH
Josef-Drexler-Str. 8, 89331 Burgau - Germany
herewith declare under our sole responsibility that the product
Brennholzwippkreissäge (Log saw) BWS 400
Serial number: 000001 – 020000
is conform with the above mentioned EC directives as well as with the
provisions of the guidelines below:
2014/30/EU and 2011/65/EU.
Following harmonized standards have been applied:
EN 60204-1:2006+A1+AC; EN 1870-6:2002+A1:2009;
EN 55014-1:2006+A1+A2; EN 55014-2:1997+A1+A2; EN 61000-3-2:2014;
EN 61000-3-3:2013
Duly authorised person for the complilation of technical documents:
ATIKA GmbH – Technical department
Josef-Drexler-Str. 8 – 89331 Burgau – Germany
i.A.
Burgau, 27.02.2017 i.A. G. Koppenstein
Engineering design management
Description of device /
J1 J2
Spare parts
Pos. Order-No.
1
2 365004
3
4
5 365007
9
6
7 365009
9
8
9
9
9
10 365010
10
12 365011
10
13 365012
10
14 365013
15 365014
10
16 365015
10
17 365016
10
18 365017
12
19 365018
12
20 365019
12 21
21A
13
22 365020
13
24 365021
14
27 365003
14
28 365022
14
29 365023
14
30 365029
14
14
Extent of delivery
15
15
•
1 Pre-assembled device unit
•
1 Saw blade (∅ 400 mm)
•
1 Jigging device
•
2 Handle
•
Saw blade casing
•
Cover
•
1 Support extension

After unpacking, check the contents of the box
 That it is complete
 Check for possible transport damage
Report any damage or missing items to your dealer, supplier or the
manufacturer immediately. Complaints made at a later date will not be
acknowledged.
Characteristics noise values
DIN EN ISO 3746 / DIN EN ISO 11202 / ISO 7960 Appendix A
Use of the machine as log saw for firewood with standard saw blade.
Noise power level Sound pressure level at the workplace
Load L = 98 dB(A)
WA
The factor of measurement uncertainty is 4 dB.
The values given are emission values and must therefore not simultaneously
represent safe workplace values too. Although there is a relationship between
emission and immersion levels, it can be reliably deduced whether additional
precautionary measures are necessary or not. Factors, which can influence the
immersion level currently existing at the workplace include the duration of the
effects, the special type of the workroom, other noise sources, etc. e.g. the
number of machines and other adjacent processes. The permissible workplace
values can also vary from country to country. This information should however
enable an improved assessment of the danger and risk to be carried out.
Denomination
Pre-assembled device unit
Brace
Motor P 1,8 KW
1
Switch
Jigging device
Recuperating bolt
Saw blade cover
Chain
Securing cotter pin
Recuperating spring
Safety chain
Saw blade casing
E13
Front saw blade flange
Saw blade (∅ 400mm x 3,0 x 2,2 x 30 x 40T)
E11
Rear saw blade flange
E13
Locking nut M 20
Cover
Handle
Support extension
Star grip knob M6x40
Star grip knob M6x20
Length stop
E6
Set of plastics insert
Safety label
Slip-on foot – small
Slip-on foot – big
Open-end wrench + Installation wrench
•
1 Saw blade cover
•
Length stop
•
Mounting accessories
•
Operating manual
•
Assembly and operating
instruction sheet
•
Warranty declaration
L = 96 dB(A)
pA
E12
9