Manufacturer's Warranty; Spare Parts Lists - Roller Uni-Press E Notice D'utilisation

eng
● Wrong pressing tongs, Mini pressing tongs, pressing ring (pressing contour,
size) or adapter tongs inserted.
● Pressing tongs, Mini pressing tongs, pressing ring or adapter tongs stiff or
defective.
5.3. Fault: A prominent burr is produced on the press fitting when closing the pressing tongs, Mini pressing tongs, pressing ring or pressing segments.
Cause:
● Damaged or worn pressing tongs, Mini pressing tongs, pressing ring,
pressing segments or pressing contour.
● Wrong pressing tongs, Mini pressing tongs, pressing ring (pressing contour,
size) or adapter tongs inserted.
● Unsuitable matching of press fitting, pipe and support sleeve.
5.4. Fault: Pressing jaws close without load on the pressing tongs, Mini pressing tongs offset at "A" and "B" (Fig. 1).
Cause:
● Pressing tongs, Mini pressing tongs fell to the floor, compression spring
bent.
5.5. Fault: The pipe is crushed between the press fitting and the fitting joint in axial pressing.
Cause:
● Expansion too long.
● Pipe pushed too wide onto the support sleeve of the press fitting.
● Wrong expanding head (press fitting system, size) inserted.
● Unsuitable matching of press fitting, pipe and support sleeve.
5.6. Fault: A prominent gap is left between the press fitting and the fitting joint after closing the pressing heads in axial pressing.
Cause:
● Pipe crushed between the compression sleeve and the fitting collar,
see 5.5.
● Wrong compression head (compression sleeve system, size) used.
● Battery depleted or defective (ROLLERʼS cordless drive units).
● Drive unit defective.
5.7. Fault: Expander does not complete the expanding, expanding head does not open fully.
Cause:
● Battery depleted or defective (ROLLERʼS cordless drive units).
● Drive unit defective.
● Wrong expanding head (press fitting system, size) inserted.
● Expanding head stiff or defective.
● Expander set incorrectly (ROLLERʼS Akku-Exparo Cu ACC).
● Distance from the press fitting to the expanding head too small.
6. Disposal
The drive units, batteries and rapid chargers may not be thrown in the household
waste when they are finished with. They must be disposed of properly by law.

7. Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product to the
first user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or renew
the warranty period for the product. Damage attributable to natural wear and tear,
incorrect treatment or misuse, failure to observe the operational instructions,
unsuitable operating materials, excessive demand, use for unauthorized purposes,
interventions by the customer or a third party or other reasons, for which ROLLER
is not responsible, shall be excluded from the warranty.
Services under the warranty may only be provided by customer service stations
authorized for this purpose by ROLLER. Complaints will only be accepted if
the product is returned to a customer service station authorized by ROLLER
without prior interference in an unassembled condition. Replaced products and
parts shall become the property of ROLLER.
The user shall be responsible for the cost of shipping and returning the product.
The legal rights of the user, in particular the right to make claims against the
seller under the warranty terms, shall not be affected. This manufacturer's
warranty only applies for new products which are purchased in the European
Union, in Norway or in Switzerland.
● Check the labelling on the pressing tongs, Mini pressing tongs, pressing ring or
adapter tongs and change if necessary.
● Do not use the pressing tongs, Mini pressing tongs, pressing ring or adapter
tongs any further! Clean and lightly grease the pressing tongs, Mini pressing
tongs, adapter tongs with machine oil or replace them with new ones.
Remedy:
● Replace the pressing tongs, Mini pressing tongs, pressing ring with new ones.
● Check the labelling on the pressing tongs, Mini pressing tongs, pressing ring or
adapter tongs and change if necessary.
● Check the compatibility of the press fitting, pipe and support sleeve. Observe
the installation and assembly instructions of the manufacturer/supplier of the
press fitting system to be pressed and contact him if necessary.
Remedy:
● Send the pressing tongs, Mini pressing tongs to an authorised ROLLER
customer service workshop for inspection.
Remedy:
● Check whether the right expanding head was used. Pipe expanded several
times, observe the installation and assembly instructions of the manufacturer/
supplier of the press fitting system to be pressed.
● Check whether the right expanding head was used. Pipe expanded several
times, observe the installation and assembly instructions of the manufacturer/
supplier of the press fitting system to be pressed.
● Change expanding head.
● Check the compatibility of the press fitting, pipe and support sleeve and
contact the manufacturer7supplier of the press fitting system to be pressed if
necessary.
Remedy:
● Check whether the right expanding head was used. Pipe expanded several
times, observe the installation and assembly instructions of the manufacturer/
supplier of the press fitting system to be pressed.
● Change pressing head.
● Charge the battery with the Li-Ion/Ni-Cd rapid charger, change the battery.
● Have it checked/repaired by an authorised ROLLER customer service
workshop.
Remedy:
● Charge the battery with the Li-Ion/Ni-Cd rapid charger or change the battery.
● Have it checked/repaired by an authorised ROLLER customer service
workshop.
● Change expanding head.
● Do not use the expanding head anymore! Clean the expanding head and
grease lightly with machine oil or change.
● Reset the expander, see 2.5.
● Increase the distance between the press fitting and the expanding head.
This warranty is subject to German law with the exclusion of the United Nations
Convention on Contracts for the International Sales of Goods (CISG).
8. Extension of the manufacturer's warranty to 36 months
It is possible to extend the warranty period of the above manufacturer's warranty
to 36 months for the drive units listed in these operational instructions which
were delivered to the first user on and after 2011-01-01. The condition for this
is that the drive unit shall be sent in for a payable inspection by an authorised
ROLLER customer service station at least every 12 months after delivery to
the first user and the data on the rating plate are legible. In the annual inspec-
tion, the drive unit is dismantled, for example, and wearable parts inspected
and usually changed. The repeated inspection of electrical equipment also
takes place according to EN 62638:2010-08 (VDE 0702). After inspection, the
authorised ROLLER customer service station issues a detailed test certificate
for the drive unit with specification of the machine number. The drive unit is
given a test badge. The date of delivery shall be documented by the submission
of the original purchase documents, compliance with the inspection intervals
shall be documented by the submission of the original test certificates. A quote
shall be made before carrying out any necessary repairs.

9. Spare parts lists

For spare parts lists, see www.albert-roller.de → Downloads → Parts lists.
eng