Krick Ro Marin Happy Hunter Notice De Montage Et De Mise En Œuvre page 47

Whip aerials, flagstocks, compass, searchlights, telephone aerial, towing cable, self-adhesive decals, spare
anchor,lighting, Figs. 201 - 207, Plan II
Part Description
No.
447 Plinth
448 Whip aerial
449 Whip aerial cap
450 Flagstock brace
451 Flagstock
452 Dutch national flag
453 Flagstock cap
454 Compass cowl
455 Compass housing
456 Searchlight
457 Searchlight plinth
458 Signal halyard
459 Dockyard flag
460 Telephone aerial
461 Towing cable
462a-x Self-adhesive decals
463 Spare anchor
464 Anchor bracket
465 Lamp
466 Steamer lamp
467 Clear bulb
468 Red bulb
469 Green bulb
470 Flexible cable
471 Heat-shrink sleeve
472 10-pin connector
- Assemble the two whip aerials for the top deck from
parts 447 - 449. Note that the wires 448 are of diffe-
rent length, as shown on the plan.
- Make up the flagstock from the brass wire parts 450
and 451, and attach it to the top deck as shown in the
plan view. Fit the Dutch national flag 452 and the cap
453 on the flagstock.
- Assemble the compass (parts 454, 455) and the
searchlights (parts 456, 457) and glue them in place
as shown.
- Tie the signal halyards 458 to the yard blocks, and the
signal yards on the foremast and mainmast. A docky-
ard flag 459 could be set at the same time.
- Run the telephone aerial 460 on the port side from the
mainmast block to the foremast block. Extend part of
the aerial to the aerial holder 316 on the funnel.
- The towing cable 461 is supplied as a length of thread
about 2500 mm long; tie a loop in each end, wrap the
ends with thread and secure the loop ends with a drop
of cyano.
- Run one end of the towing cable through the opening
in the aft bulkhead and into the hull, where it should
be connected to the towing mechanism. Coil up the
other end and position it on the after deck behind the
hawser bars.
- Bend the anchor brackets 464 to the shape shown,
and use them to attach the spare anchor 463 to the aft
superstructure wall.
Material
Plastic
Brass
Glass
Brass
Brass
Fabric
Glass
Plastic
Beech
Metal
Spruce
Thread
Fabric
Thread
Thread
---
Metal
Brass
Plastic
Plastic
---
---
---
---
---
---
© Klaus Krick Modelltechnik, Germany, Stand 06.2017
Size in mm
Inj. moulded
1 Ø
4 O.D.
0.7 Ø
1 Ø
Ready made
4 O.D.
Inj, moulded
8 Ø x 21
Ready made
8 x 8 x 12
0.2 Ø
Ready made
0.2 Ø, 2-part
1 Ø x 2500
---
Ready made
1 Ø
5.4 Ø x 12, inj.
5.4 Ø x 12, inj.
3 Ø, 6 Volt
3 Ø, 6 Volt
3 Ø, 6 Volt
0.07 mm²
2.4 Ø
---
The lighting system
- Install the bulbs 467 - 469 as shown in the "Lamp as-
sembly" diagram on Plan II. Note the correct location
of the coloured bulbs. Extend the connecting wires
470 to suit, and run them downward. The bulbs should
be wired up in parallel. We recommend that you install
a 10-pin connector 472 in the wiring harness to enable
you to remove the superstructure at any time. The
stern lamp should also be connected using a plug and
socket.
- Position the lamps 456 and 466. Glue the navigation
lamps in place after fitting the bulbs from the undersi-
de.
Note on lighting system
The wiring diagram shows the method of connecting the
bulbs to the three unused Multi-Switch channels.
If you wish to install a scale lighting system, at least one
additional electronic switching facility is required. The
separate sheet entitled "Lighting system" shows how the
individual groups of lamps are wired together and con-
nected to the individual channels.
Your model is now complete.
No. Notes
off
3
3 As plan
3 FS, bead
1 As plan
1
1 FS
1 FS, bead
1 FS
1
2 FS
2
10 FS, as plan
1 not included
1 FS, as plan
1 FS
1 Set
1 not included
1 As plan
5 FS
8 FS
10 FS
4 FS
1 FS
1 Not included
1 Not included
1 Not included
23