Krick Ro Marin Happy Hunter Notice De Montage Et De Mise En Œuvre page 30

hull. Snip off the front arm of the right-hand tiller - Fig.
27.
- Glue the servo support plate 38 to the keel in-fill piece
and the Kort nozzles, in the position shown on the
plan.
- Fit the rudder servo 39 in the servo mount 40 A + B,
and place the mount on the servo support plate, but
do not secure it at this stage. Set the servo to centre
and move both rudders to the "straight ahead" positi-
on. Align the tillers carefully, press them down lightly
and tighten the sockethead screws 37.
- Connect the system using the pushrods 41 - 44. Align
the servo, and attach the servo mount to the servo
support - Figs. 28, 29.
The after deck
Part Description
No.
57, 58 Frame
59 After deck
60 Deck girder
61 Deck girder
62,63 Hatch cover
64 Swivel latch
65 Countersunk screw
66-69 Frame side panel
70 After deck support girders
71 Reinforcing rail
72 After bulkhead
73 Support rail
74 Door
75 Companionway wall
76 Companionway wall
77 Reinforcing rail
78 Front roller box wall
79 Roller box doubler
80 Roller box cover
81 Roller box side panel
- Note: while you are working on the after deck please
take care not to assemble it the wrong way round.
- Mark the position of the frames 57 and 58 on the un-
derside of the after deck 59, and glue them in place.
- Glue the deck girders 60, 61 in place leaving 3 mm
spacing to the edges of the deck - Fig. 43.
- Trim the hatch covers 62, 63 and fit them. Fit the swi-
vel latches 64, 65 - Fig. 44.
- Glue the frames 66, 67 and 68, 69 to the underside of
the hatch covers - Fig. 45.
- Attach the deck support girders 70 just below the
upper marked line in the hull. The butt joint should be
located in the centre of the transom - Fig. 46.
- Clamp the support girders to the hull, ensure there are
no gaps, and glue them in place by running drops of
cyano along the joints.
- Cover the installed RC and power system compo-
nents to protect them. Trial-fit the after deck, trim it as
6
Bow thruster
Material
ABS
ABS
ABS
ABS
ABS
Plastic
Steel
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
After bulkhead and roller box
© Klaus Krick Modelltechnik, Germany, Stand 06.2017
- Assemble the bow thruster 1 B as described in the
instructions supplied with the set.
- Suppress the motor using the suppressor set 168, and
- solder the cables 2 B to the motor.
- Tape the bow thruster tubes 3 B together, and trim the
holes in the hull to obtain as snug a fit as possible.
Take care to set the bow thruster horizontal - Figs. 35
- 37.
- Assemble the bow thruster inside the hull, align it ca-
refully and mark the excess length of the outer tubes.
- Shorten the tubes at the marked points and glue them
to part 1 B. Glue the bow thruster in the hull, taking
great care to make the joints watertight. Sand back
the excess tube length flush with the hull - Figs. 38 -
41.
Size in mm
1.5, laser-cut
1.5, laser-cut
1.5, laser-cut
1.5, laser-cut
1.5, laser-cut
Inj. moulded
2.2 Ø x 6.5
1.5, laser-cut
2 x 2, as plan
3 x 3, as plan
1.5, laser-cut
2 x 2, as plan
1, laser-cut
1.5, laser-cut
1.5, laser-cut
3 x 3, as plan
1.5, laser-cut
1.5, laser-cut
1.5, laser-cut
1.5, laser-cut
required, and glue it in place. Sand the hull down flush
with the after deck in the stern area - Fig. 47.
- Cut the reinforcing rail 71 to a length of 211 mm, and
glue it in place - Fig. 49.
- Glue the support rail 73 to the inside of the after bulk-
head 72, and stick the door 74 on the outside - Figs.
50, 51.
- Trim the after bulkhead to fit, and glue it in place - Fig.
52. - Glue the companionway walls 75 and 76 in place
together with the trimmed reinforcing rails 77 - Fig. 53.
It is a good idea to paint the interior of the companion-
way grey at this point, as it will be inaccessible later.
- Assemble parts 78 - 81 to form the roller box - Figs.
54, 55.
- Glue the completed roller box centrally to the after
deck, allowing for the thickness of the stern bulwark
82, which will be fitted later - Fig. 56.
No. Notes
off
1 each plate 3
1 plate 2
2 plate 3
1 plate 3
1 each plate 1
12
12
2 each plate 1
2
1
1 plate 2
1
1 plate 7
1 plate 3
1 plate 2
5
1 plate 2
1 plate 2
1 plate 2
2 plate 2