Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Fitting out the after deck and the forecastle deck, Figs. 145 - 152, Plan 1
Part
Description
No.
279
Hawse barrier
280
Two-part hawse
281
Hawser pulley
282
Hawser block
283
Small return roller
284
Double cruciform bollard
285
Towing complex
286
3" Smith brake
287
Brake shoe
288
Stub
289
Elbow fitting
290
Front connection
291
Oil valve
292
Rear oil connection
293
Mechanical valve
294
5" valve
295
Gooseneck
296
Guard cradle
297
Vertical guard
298
Capstan gearbox
299
Capstan drum
300
Axle
301
Fire extinguisher box 5 x 10 x 13
302
Shield
303
Return pulley
304
Pulley pin
- Drill the holes for the hawse barrier 279 in the hatch
63. Glue the two-part hawses 280 in the barrier, and
position this assembly on the boat (see Fig. 182 for
the components).
- Drill the holes in the roller box 78 - 81 and glue the
hawser pulleys 281 and the hawser blocks 282 in
place.
- Glue the return pulleys 283 to the bulwark. Remove
the base plates of the double cruciform bollards 284,
which are glued to the main deck bulwark. Glue all the
bollards 284 in place in the positions shown.
- Glue parts 285 and 286 in place.
- Drill the appropriate holes in the after deck. Position
parts 287 - 295 as shown in the plan view and the
detail views.
The funnels, Figs. 153 - 159
Part
Description
No.
305
Internal funnel wall
306
Lower centre floor
307
Floor
308
Funnel shell
309
Funnel fairing
310
Large exhaust pipe
311
Small exhaust pipe
312
Large air shaft
313
Small air shaft
314
Funnel door
Material
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
Aluminium
Aluminium
Brass
Ply wood
foil
Aluminium
Brass
Material
ABS
ABS
ABS
ABS
ABS
ABS
Brass
ABS
ABS
ABS
© Klaus Krick Modelltechnik, Germany, Stand 06.2017
Size in mm
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Inj. moulded
Machined
Machined
2 Ø x 22
5, laser-cut
0.4 x 38 x 23
6 Ø x 2
2 Ø x 4.5
The capstans
- The capstans are assembled from parts 296 - 300; note
that the end of the axles 300 must be splayed slightly
before fitting. Glue the capstans 298 - 300, the guard
cradles and the vertical guards 296, 297 on the deck.
Parts 301 - 304
- Apply the decal "F" to the fire extinguisher box, and glue
it to the after bulkhead.
- Cut the towing winch compartment shields 302 to a
length of 23 mm. Cut slots in the after bulkhead as
shown in the detail view, and glue the shields over the
openings.
- Install the return pulleys 303 on the forecastle deck
using the pins 304. Splay one end of the pins and cut
them to length after fitting them. Apply a fillet of DELU-
XE Fusion Acrylit or UHU Acrylit round the projecting
ends.
Size in mm
1.5, laser-cut
1.5, laser-cut
1.5, laser-cut
1.5
1.5, laser-cut
10 outer Ø x 7
4 outer Ø x 7
1, laser-cut
1, laser-cut
1, laser-cut
No.
Notes
off
1
2
2
FS
2
FS
2
FS
11
FS
1
FS
2
FS
2
FS
2
FS
2
FS
4
FS
4
FS
4
FS
1
FS
2
FS
6
FS
2
FS
2
FS
2
2
2
1
plate 8
2
not included
4
4
No.
Notes
off
2
plate 2 + 6
4
plate 6
2
plate 6
1 each
L/R, vac.
2
plate 6
4
4
4
plate 7
1
plate 7
2
plate 7
17
Publicité
Table des Matières
