Krick Ro Marin Happy Hunter Notice De Montage Et De Mise En Œuvre page 32

Assembling the crane
Part Description
No.
1 K R.H. crane outrigger
2 K L.H. crane outrigger
3 K Outrigger pulley
4 K Hydraulic ram
5 K Idler drum
6 K Spigot
7 K Rear bar
8 K Centre bar
9 K Front bar
10 K Hydraulic cylinder
11 K Guide tube
12 K R.H. crane post
13 K L.H. crane post
14 K Vent pipe
15 K Hydraulic motor
16 K Operator's stand
17 K Operator's desk
18 K Ladder
19 K Crane pulley
20 K Hook
21 K R.H. hook block
22 K L.H. hook block
23 K Drum
24 K Crane column
25 K Crane plinth
26 K Washer
27 K Collet
28 K Grubscrew with cutter tip
104 Guide tube
105 Bevel gear
106 Grubscrew with cutter tip
- Refer to the detail drawing on Plan I and photos 73
- 85. The crane should be assembled following the
sequenceof the part numbers.
- Parts 3 K - 5 K must be free to move.
- Glue the guide tube 104 to the top end of the tube 11
K only; take care to cut the tube to the correct length.
- Glue the tube 11 K in the right-hand crane post 12 K.
Assemble the crane outrigger 1 K - 9 K, place it in the
right-hand crane post, and glue the left-hand crane
pos 13 K on top.
- Install parts 14 K - 18 K as shown in photo 79.
- When assembling the crane hook ensure that the
pulley 19 K and the hook 20 K are free to move.
- Glue parts 23 K - 25 K together. Place the completed
crane plinth on the guide tube and check that it swi-
vels smoothly.
- Fit the completely assembled crane through the hole
in the main deck, and glue the crane plinth to the
deck.
- Secure the crane using parts 26 K - 28 K, ensuring
that it rotates freely. Fix the spur gear 105/106 to the
8
Material
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
Brass
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
Brass
Brass
Steel
Brass
Brass
Steel
© Klaus Krick Modelltechnik, Germany, Stand 06.2017
Size in mm
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
4 O.D. x 75
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
Inj. Moulded
4.3 Ø x 9 Ø
4 I.D.
M3 x 3
1 Ø x 0.6 Ø x 80
11.2 Ø
M3 x 3
tube 11 K.
- Note: the next stage is to assemble the mechanical
parts for the auxiliary working systems. We recom-
mend that you start by fitting the suppressor sets 168
to the miniature geared motors. Solder the connec-
ting leads to the terminals at the same time. Note:
a connector 187 should be fitted in the crane swivel
mechanism.
No. Notes
off
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1 FS
2 FS