Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Boatstand
Part
Description
No.
S-1
Base plate
S-2, S-3 Hull support
04
Support strip
Assemble the boatstand from parts 01 - 03 and glue the joints. The foam rubber strips for protecting the pain-
ted hull are not required until later - Figs. 1 - 2 slightly different.
Preparing the hull, power system
No.
1
Hull
2
Keel in-fill piece
3
Kort nozzle
4
Propeller shaft tube
5
Support
7
6, 8
Speed controller support former
9
Speed controller support side
10
Speed controller support former
11
Motor bulkhead
12
13
Electric motor
14
Motor mounting screw
15
Washer
16
Capacitor
17
Capacitor
18
Cable
19
Cable
20
Connector
21
Coupling
22
Grubscrew
23
Lubricating tube
24
Propeller shaft
25
Collet
26
Grubscrew
27
Locknut
28
Propeller
29
Bottom rudder bush
30
Countersunk screw
- Cut out the hull 1 along the marked lines, leaving 1 -
1.5 mm excess at the areas marked with arrows. The
remainder should be sanded back until the marked
lines are still just visible.
- Trim the keel in-fill piece 2 to fit and glue it in place -
Figs. 3 - 6.
- Cut the slots for the Kort nozzles, and drill the holes
for
- the propeller shaft tubes and the rudder bushes.
- Cut out the hole for the bow thruster, working just
inside the marked lines - Figs. 7 - 9
The power system
Note: the whole power system and rudder system are in-
itially assembled and aligned inside the model. Only then
are these parts glued to the hull.
4
Material
Ply wood
Ply wood
Foam rubber
Material
ABS
Balsa
Plastic
Brass
ABS
ABS
Ply wood
---
Brass
---
---
---
---
---
Aluminium
Steel
The motors can be controlled using either one speed
controller or two. Separate motor control provides greater
manoeuvrability of the finished model.
Photos 17 and 18 show the motors wired together to a
single controller; if you wish to install the version with two
controllers, refer to the wiring diagram on Plan II. Please
study this before starting construction, and attach the
appropriate cables and connectors to the motors.
© Klaus Krick Modelltechnik, Germany, Stand 06.2017
Size in mm
5, laser-cut
5, laser-cut
6 x 4
Size in mm
3, vac.-moulded
8 x 100 x 103
Inj. moulded
6 O.D. x 267
1.5, laser-cut
1.5, laser-cut
3, laser-cut
Ready made
M4 x 10
4.3 x 9 x 0.7
100 nF
47 nF
1.5 mm²
1.5 mm²
Ready made
4 / 5 Ø x 17
M3 x 3
4 Ø x 0.4 x 55
4 Ø x 300
M3 x 3
M4
60 Ø, inj. moulded 2
Inj. moulded
2.2 Ø x 6.5
- Fit the Kort nozzles 3 and stern tubes 4 - Fig. 11.
- Assemble the speed controller support from parts 5 -
10 as shown in Figs. 12 and 13.
- Temporarily fit the speed controller support and the
motor bulkhead assembly 11 / 12 in the hull - Figs. 14
and 15.
- File a flat area in the shafts of the motors 13 to accept
No.
Notes
off
1
plate 8
1 each
plate 8
2
Not included
No.
Notes
off
1
1
Oversize
1 each
Left / right
2
1
plate 1
1
plate 1
plate 1
2
plate 1
1
plate 1
1
plate 9
2
plate 9
2
PS
4
PS
4
PS
4
PS
2
PS
1
PS, overlength
1
PS, overlength
2 - 4
Not included
2
PS
4
PS
2
2
2
2
2
L.H. / R.H.
2
4
Self-tapping
Publicité
Table des Matières
