Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
and glue the end-supports to the base plate. Attach
the side panels 159 and the gussets 160.
- Drill a 1 mm Ø hole in the drum.
Radar drive unit
Part
Description
No.
164
Motor support
165
Motor, geared 1000 : 1
166
Spacer block
167
Self-tapping screw
168
Suppressor set
Refer to the detail drawing on Plan 2 and photos 103 and
104.
- Screw the motor 165 to the motor support 164. Fix
the spacer blocks 166 to the motor support using the
RC installation and wiring
Part
Description
No.
169
Receiver
170
Receiver battery cradle
171
Receiver battery
172
Y-lead
173
Relay
174
Wire
175
Spade connector
175a
Distributor
176
Charge lead
177
Relay
178
Extension lead
179
Bow thruster speed controller
180
Spade connector
181
Sound module
182
Bass loudspeaker
182a
Bass loudspeaker housing
182b
Self-tapping screw
183
Multi-Switch decoder 16
184
Decoder servo lead
185
Transistor reversing module
186
Servo lead with plug
187
BEC lead with socket
188
Self-tapping screw
189
Servo lead
RC system installation and wiring, wiring plan on
Plan II, Figs. 105 - 111
Note: please refer to the instructions supplied with the
electronic units before carrying out the wiring procedures.
Use servo extension leads where required to connect the
individual RC components.
The full wiring system consists of three power cir-
cuits:
- 4.8 V (receiver battery, No. 171) for receiver, servos
and decoder.
- 6 V (battery, No. 47) via a relay for bow thruster, ligh-
ting, and geared motors for auxiliary working systems.
- 12 V (drive batteries, No. 53) via a relay for drive mo-
tors and sound module.
Material
ABS
---
Ply wood
Steel
---
All the completed drive systems are installed in the hull
once the RC system has been fitted and the auxiliary
working systems have been wired up.
Material
---
ABS
---
---
---
Brass
---
---
---
---
---
---
---
---
---
ABS
Steel
---
---
---
---
---
Steel
---
Base functions
© Klaus Krick Modelltechnik, Germany, Stand 06.2017
- Screw the completed anchor winch to the mounting
plate 150 using the self-tapping screws 163.
Size in mm
1.5, laser-cut
---
5, laser-cut
2.2 Ø x 6.5
---
selftapping screws 167.
Size in mm
---
1.5
---
---
---
1.5 Ø
6.3
---
---
---
---
---
---
---
---
1.5
2.9 Ø x 6.5
---
---
---
---
---
2.2 Ø x 6.5
---
- The 6 V and 12 V power circuits are switched on and
off using relays which are connected to the receiver.
The circuits are switched automatically when the
receiving system is turned on and off using the slide
switch 129.
- Attach the receiver 69 and the receiver battery cradle
170 using Velcro (hook-and-loop) tape, and fit the
receiver battery 171 in the cradle. Connect the battery
to the receiver using the switch harness 129 and the
Y-lead 172.
- Withdraw the red wire from the receiver connector
attached to the speed controller 45; it is not required
when a BEC system is employed.
No.
Notes
off
1
plate 5
1
Not included
2
plate 8
2
6
Not included
No.
Notes
off
1
Not included
1
Vac. moulded
1
Not included
3
Not included
1
Not included
2
2
Not incl. ro4039
3
Not incluced
1
Not included
1
Not included
1
Not included
1
Not included
2
Not included
1
Not included
1
Not included
1
Vac. moulded
4
1
Not included
2
Not included
4
Not included
1
Not needed
1
Not incl. 67522
6
1-3
Not included
11
Publicité
Table des Matières
